To improve customer satisfaction in relation to the Becker® MAP PILOT (NAVBOX45) control unit, we would like to draw your attention to the following procedure for technical queries and handling updates for map data and the navigation software.
System components
The basis is code E1N (Becker MAP PILOT). Both the map data required for navigation and the navigation software are on the Becker® MAP PILOT (NAVBOX45) control unit. The Becker® MAP PILOT (NAVBOX45) control unit contains several navigation software modules, which are updated via different interfaces and tools. The figure below shows the structure of the Becker® MAP PILOT (NAVBOX45) control unit:
P82.61-4153-78
Communication between the Becker® MAP PILOT (NAVBOX45) control unit and the vehicle takes place using the interface software. The navigation mode is implemented through the navigation software and the firmware. The map data required for navigation are filed on the internal device memory. An SD card with updated map data can also be used for navigation. The map data stored on the SD card have a higher priority than the map data of the internal device memory. The map data cannot be transferred from the SD card to the internal device memory.
Operating instructions
The operator's manual in the form of a PDF file is stored on the Becker® MAP PILOT (NAVBOX45) control unit. To view the operator's manual, the Becker® MAP PILOT (NAVBOX45) control unit must be connected to a suitable PC via the USB interface using the supplied USB connecting cable. The operator's manual can also be downloaded at www.beckermappilot.com or purchased in printed form from the parts service under a corresponding B6 part number . Additional information is available in the ODUS system of MercedesBenz Accessories GmbH.
Update the interface software through XENTRY Diagnostics
The interface software on the Becker® MAP PILOT (NAVBOX45) control unit can only be updated using XENTRY Diagnostics via the CAN bus. As usual the software is automatically provided via XENTRY Diagnostics and it can be updated via the menu item Adaptations Control unit programming.
Updating of the map data, navigation software and firmware via the Becker® Content Manager
Using the Becker® Content Manager
The navigation software and firmware on the Becker® MAP PILOT (NAVBOX45) control unit, and the map data can only be updated on the PC using the Becker® Content Manager. This is stored on the Becker® MAP PILOT (NAVBOX45) control unit and alternatively can also be downloaded from the Becker® online shop at www.beckermappilot.com.
System requirements for Becker® Content Manager
A commercially available PC with USB 2.0, Microsoft® Windows® or with Apple® Mac OS X version, Internet connection and approx. 16 GB of free memory is required to be able to use the Becker® Content Manager. Administrator rights are required for installation and updating the Becker® Content Manager.
Operating systems compatible with Becker® Content Manager
Microsoft® Vista, Win7/8/8.1/10: for all Becker® MAP PILOT device types.
Apple® OSX 10.7 (Lion) to 10.10 (Yosemite): only for Becker® MAP PILOT device types 9077, M013, M041, M045, M046, M050 and M051.
Apple® OSX 10.8 (Mountain Lion) or newer: only for Becker® MAP PILOT device types M054, M075, M076, M083, M084, M085, M092, M097 with firmware R24 or newer.
Data transfer for update procedure
Data is transferred from the PC to the Becker® MAP PILOT (NAVBOX45) control unit via the USB interface using the USB connecting cable supplied by Becker®. For this purpose, the Becker® MAP PILOT (NAVBOX45) control unit must be pulled out of the mount in the vehicle.
Questions and answers
If you have any queries concerning the Becker® Content Manager or concerning any problems that arise during the update procedure, contact the Becker® Hotline. The contact data are available at www.beckermappilot.com. A list of FAQs is also located there, it contains the answers to the most frequently asked questions.
For customers and dealers
Updating of the navigation software and firmware via the Becker® Content Manager can be conducted by the dealer responsible for the vehicle or by the customer himself.
The map data can also be updated through the Becker® Content Manager. The map data can be updated free of charge up to 60 days after the system has been put into service in the vehicle. The customer is to be notified of this 60day deadline when handing over a new vehicle. An extension of this 60day deadline after the in-service date is no longer possible. If requested by the customer, an update of the map data can be performed by the dealer during this time period. A cost settlement through warranty or goodwill is not possible.
After expiry of the 60day deadline, map data updates can be downloaded chargeable through the Becker® Content Manager in the Webshop. A credit card is required here for payment purposes.
As an alternative to the chargeable map update through the Becker® Content Manager, MercedesBenz Accessories also offers map data on an SD card for various national versions. Further information is available in the ODUS system of MercedesBenz Accessories GmbH.
It should be noted that the inserted SD card is not recognized by the Becker® Content Manager. Therefore, when using the Becker® Content Manager, a message may be issued declaring that the map data on the Becker® MAP PILOT (NAVBOX45) control unit is obsolete, despite the map data on the SD card being up to date.
Preconditions and time required
For navigation, the Becker® MAP PILOT (NAVBOX45) control unit must remain inserted in the mount in the vehicle, otherwise the data will not be transferred to the radio.
The time required for an update of the navigation software, firmware or map data using the Becker® Content Manager may last for several hours. This is dependent on the required content and the bandwidth of the Internet connection.
If more than one Becker® MAP PILOT (NAVBOX45) control unit with the same contents (Becker® Content Manager, operator's manual as PDF, firmware) is to be updated, the contents do not need to be downloaded to the PC multiple times.
System check
XENTRY Diagnostics is required to check the system components of the Becker® MAP PILOT, the line connection as well as navigation mode. Various tests are available in Xentry Diagnostics.
Special tools (e.g. a test card) are not necessary.
Operation items and damage code
The following operation items are available for a map data or software update:
82-9900 Update map data for navigation system
82-9920 Update software for navigation box (only on model 447)
The following damage codes are valid for the Becker® MAP PILOT:
5131M Connector/line bracket for Becker® MAP PILOT
53632 Traffic Info/dynamic destination-oriented navigation system function (only on model 447)
5930N Connector/line Becker® MAP PILOT
8208C Rechargeable battery Becker® MAP PILOT
8210S Navigation function (only on model 447)
8280N Becker® MAP PILOT (accessories)
8700G Becker® MAP PILOT holder (accessories)
Referenced documents
- gf8261d2003h Navigation, function
- gf8261s2003tra Navigation, function