W01.45-1039-09
1 | Charge air pipe | 6 | Coolant pipe | 10 | Hydraulic line | ||
2 | Guide pulley | 7 | Hydraulic pump | 11 | Bracket | ||
3 | Carrier with guide pulley | 8 | Oil pan | 12 | Charge air pipe | ||
4 | Poly-V belt tensioning device | 9 | Bracket | G2 | Alternator | ||
5 | Alternator carrier |
W01.45-1038-09
8 | Oil pan | 16 | Bracket | 19 | Hydraulic line (steering) | ||
14 | Bracket | 17 | Bracket | B14 | Oil level sensor | ||
15 | Charge air pipe | 18 | Bracket |
| Remove/install | ||
Warning | Risk of injury to skin and eyes suffering scalding from contact with hot coolantspray. Risk of poisoning from swallowing coolant. | Do not open cooling system unless coolant temperature is below 90 °C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers. | |
1 | Switch off ignition | ||
2 | Open maintenance flap | ||
Warning | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure it with the safety strut. | |
3 | Tilt cab | ||
Topical note | Notes on tilting the cab | ||
Danger | Risk of fire/risk of explosion due to short circuit and escaping oxyhydrogen gas. Risk of (burn) injury caused by caustic burns to eyes, skin and mucous membranes from battery electrolyte/mist, short circuit and arcing. Risk of poisoning caused by swallowing battery electrolyte or absorption of lead through the skin or body orifices. Risk of death due to voltage U >= 30 V AC and U >= 60 V DC. | No fires, sparks, open flames, or smoking. Wear acid-resistant gloves, clothing, and glasses. Pour battery acid only into suitable and appropriately marked containers. | |
4 | Disconnect ground line from battery | ||
Topical note | Notes on battery | ||
5 | Remove soundproofing to right, left of frame at top, and soundproofing and underride guard on the frame at the bottom | Installation: Do not install the soundproofing or underride guard until after the leaktightness test. | |
6 | Suction off engine oil with engine oil extractor or drain engine oil |
| |
Notes on engine oil | |||
Engine 902.9 except code MS8 (natural gas engine), engine 926.9 | |||
Oil drain screw to oil pan | |||
Engine oil | |||
7 | Remove hydraulic pump (7) | ||
8 | Remove coolant pipe (6) and hydraulic line (10) from the bracket (9) | ||
9 | Remove bracket (9, 11) at front from the oil pan (8) | ||
10 | Remove charge air pipe (1) from the charge air cooler to the charge air manifold |
| |
Engine 902.9 except code MS8 (natural gas engine), engine 926.9 | |||
Engine 906.9 except code MS8 (natural gas engine) | |||
11 | Remove charge air pipe (12) | Clamp, charge air hose to charge air manifold/charge air pipe and charge air cooler | |
12 | Remove guide pulley (2) from the oil filter | ||
13 | Remove the carrier with guide pulley (3), poly-V belt tensioning device (4) together with the alternator carrier (5) and bind it to the frame | Do not remove electrical lines, electrical wiring harness or alternator (G2). | |
Screw/bolt, alternator carrier to cylinder crankcase | |||
14 | Remove charge air pipe (15) from exhaust gas turbocharger to charge air cooler |
| |
Engine 902.9 except code MS8 (natural gas engine), engine 926.9 | |||
15 | Remove the bracket (14) of the charge air pipe (15) on the right from the oil pan (8) | ||
16 | Remove the bracket (16) of the charge air pipe (15) on the right from the cylinder crankcase | ||
17 | Remove the bracket (18) of the hydraulic line (19) from the oil pan (8) on the left | Do not disconnect hydraulic line (19). | |
18 | Disconnect the electrical connector of the oil level sensor (B14) from the engine control (MR) control unit | ||
19 | Expose the electrical line and remove the oil level sensor (B14) from the oil pan (8) | Installation: Check the sealing ring on the oil level sensor (B14) for damage; if necessary, replace the oil level sensor (B14). | |
Oil level sensor to oil pan | |||
20 | Remove the oil pan (8) and pull it out to the front | Bolt, oil pan to cylinder crankcase | |
21 | Remove seal | ||
22 | Install in the reverse order | ||
23 | Check engine oil level with oil dipstick or on display, add oil if necessary | Observe engine oil grade set in maintenance system or Specifications for Operating Fluids. | |
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
24 | Start engine and allow to run in idle for 10 s until the oil pressure has built up, then run the engine at varying speeds | ||
25 | Switch off engine and check for leaktightness | Visual inspection. | |
26 | Synchronize the time of the tachograph disk record | Only in vehicles with modular tachograph. |
Henviste dokumenter
- ah1800n010101ha Oplysninger om motorolie
- ah5410p000101a Oplysninger om batterier
- ah5410p000101a
- ah6080n000301a Oplysninger om tipning af førerhus
- ar0941w1311c
- ar0941w1311d
- ar0941w1311h
- ar0941w1311jb
- ar0941w1311jd
- ar1800w303502a
- ar1800w303502j
- ar2040w0400a
- as0000z000501a Fare for ulykke ved automatisk igangsætning når motoren kører. Fare for personskade på grund af knusning og forbrænding, hvis der arbejdes mens motoren startes eller kører
- as2000z000101a Risiko for skoldningsskader på hud og øjne pga. sprøjtende, varm kølervæske. Risiko for forgiftning ved indtagelse af kølervæske
- as5410z000101a Brand-/eksplosionsfare på grund af kortslutning og udsivende knaldgas. Forbrændingsfare/fare for personskade ved ætsning af øjne, hud og sliminder på grund af batterielektrolyt/-tåge, kortslutning og lysbuepåvirkning. Fare for
- as6080z000101a Fare for personskade ved fastklemning og knusning, når førerhuset tippes