Modification notes
This Service Information is only valid for workshops that have authorization to install the toll system from Toll Collect.
We have created the following installation instructions for retrofitting the toll system (automatic recording of freeway tolls).
Work units for retrofitting the toll system from Grundig
Cate-gory | Op. no. | Operation text | CVs before 1996 | ACTROS Type 950-954 | ACTROS Type 930-934 | ATEGO >18 t | ATEGO <15 t | AXOR |
Family | 10.03, 10.06, 10.09, 10.13, 10.14 | 10.18 | 10.42 | 10.18 | 10.21 | 10.33 | ||
N | 82 9530 | Retrofit toll system Grundig | 47 | 51 | 47 | 52 | 47 | 60 |
N | 82 9549 | In addition to Retrofit toll system, Remove/install curtain rail (location) | --- | --- | --- | 7 | 7 | --- |
Work units for retrofitting the toll system from Siemens VDO
Cate-gory | Op. no. | Operation text | CVs before 1996 | ACTROS, Type 950-954 | ACTROS Type 930-934 | ATEGO >18 t | ATEGO <15 t | AXOR |
Family | 10.03, 10.06, 10.09, 10.13, 10.14 | 10.18 | 10.42 | 10.18 | 10.21 | 10.33 | ||
N | 82 9537 | Retrofit toll system Siemens VDO | 41 | 41 | 39 | 42 | 37 | 50 |
N | 82 9549 | In addition to Retrofit toll system, Remove/install curtain rail (location) | --- | --- | --- | 7 | 7 | --- |
All times do not include test driving vehicle for initializing the GPS receiver and instructing the customer on the use of the toll system device.
Performing a test drive: Drive at least 2000 meters with a minimum of 30 km/h in each of the compass directions (N, S, E, W)
Grundig toll recording devices
Retrofit toll system | MODEL 950.0/1/2/3, 952.0/1/2/3, 953.1/3, 954.0/1/2 up to VIN end no. 472725 with high cab roof or Megaspace cab with FTCO tachograph | ||
Retrofit toll system | MODEL 950.0/1/2/3, 952.0/1/2/3, 953.1/3, 954.0/1/2 as of VIN end no. 472726 with high cab roof or Megaspace cab with MTCO or TVI tachograph | ||
Retrofit toll system | MODEL 950.0/1/2/3, 952.0/1/2/3, 953.1/3, 954.0/1/2 up to VIN end no. 472725 with low cab roof and FTCO tachograph, except for car transporters | ||
Retrofit toll system | MODEL 950.0/1/2/3, 952.0/1/2/3, 953.1/3, 954.0/1/2 as of VIN end no. 472726 with low cab roof and MTCO tachograph, except for car transporters | ||
Retrofit toll system | MODEL 930-934 with high cab roof or Megaspace cab | ||
Retrofit toll system | MODEL 930-934 with low cab roof, except for car transporters | ||
Retrofit toll system | MODEL 970-976 with short (S) and long (L) cabs, except for cabs with high roof and telematics preinstallation | ||
Retrofit toll system | MODEL 950.5/6, 952.5/6, 953.6, 954.5 with short (S) and long (L) cabs, except for cabs with high roof and telematics preinstallation | ||
Retrofit toll system | MODEL 944 with long (L) cabs, except for cabs with high roof and telematics preinstallation |
W82.88-1149-01
Siemens VDO toll recording devices
The Siemens VDO toll recording device (vehicle device 1372) is to be installed as per the instructions included in the installation kit.
Furthermore, the following information is to be observed:
ACTROS, 950 - 954
In order to ensure that the controls can be accessed from the driver seat, the vehicle device (1) must be installed as far to the left of vehicle center as possible as per the permissible dimension (dimension A). The best installation position can be reached by using a 20° bracket with both of the bracket's feet pointing towards the cabs interior.
Dimension a =300 mm
Contrary to the installation instructions that were published up to now (where the milage signal is taken directly from the tachograph), the milage signal can also be taken from the maintenance system control unit (WS)
(plug X1, chamber 18/15).
W82.88-1150-01
ACTROS, 930 - 934
The installation clearance of the vehicle device to the windshield can be larger than what is stated in the instructions from Siemens VDO.
The vehicle device (1) is to be installed at the very left of the dashboard's center shelf so that the smallest distance to the windshield can be reached. In order to achieve this, the rubber insert located in the shelf must be cut out in the area of the feet. The best installation position can be reached by using a 20° bracket with both of the bracket's feet pointing towards the windshield.
W82.88-1151-01
ATEGO, 970 - 976, 950.5/6, 952.5/6, 953.6, 954.5, AXOR, 944
The installation distance of the vehicle device to the center of the vehicle can be larger than what is stated in the instructions from Siemens VDO.
The vehicle device (1) is to be installed to the left of the stowage compartment or folding table so that the compartment can still be opened. The best installation position can be reached by using a 10° bracket with both of the bracket's feet pointing towards the windshield.
参照文書
- an8288w0001a 走行料金システムの後装着
- an8288w0001b 走行料金システムの後装着
- an8288w0001c 走行料金システムの後付け
- an8288w0001d 走行料金システムの後付け
- an8288w0001lka
- an8288w0001lkb
- an8288w0001lkc 走行料金システムの後装着
- an8288w0001mpa 走行料金システムの後装着
- an8288w0001mpb 走行料金システムの後装着