Vehicle with front expansion reservoir |
1 | Cap |
W20.30-1022-11
Vehicle with rear expansion reservoir |
1 | Cap |
W20.30-1023-11
2 | Engine radiator |
3 | Drain screw |
W20.20-1080-11
Shown on engine 471.9 |
4 | Fuel filter module |
5 | Coolant drain fitting |
W20.00-1059-11
Vehicle with code B3H (Secondary-water-retarder) |
6 | Drain screw (with magnet) |
7 | Retarder |
8 | Drain screw |
W20.00-1098-11
Warning | Risk of injury. Moving parts can pinch, crush or, in extreme cases even sever extremities. | No parts of the body or limbs should be within the operating area of mechanical components when moving components. | |
Warning | Risk of injury. Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | |
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
Danger | Risk of death to implant wearers from working on retarder | As a safe distance from the retarder, a minimum distance of 100 cm is to be maintained between the retarder and the body parts of the affected person for people with implants.Nur bei Fahrzeugen mit Code B3H (Sekundär-Wasser-Retarder). | |
Warning | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure it with the safety strut. | |
Warning | Risk of injury to skin and eyes suffering scalding from contact with hot coolantspray. Risk of poisoning from swallowing coolant. | Do not open cooling system unless coolant temperature is below 90 °C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers. | |
Topical note | Notes on avoiding damage through contamination and foreign objects | ||
Topical note | Notes on influence of retarder on coolant/coolant sludging | Nur bei Fahrzeugen mit Code B3H (Sekundär-Wasser-Retarder). | |
Topical note | Notes on tilting the cab | ||
Topical note | Notes on coolant | ||
Drain off | |||
1 | Open maintenance flap. | ||
2 | Unscrew cap (1). | ||
3 | Set heating to max. heating output and switch on ignition. | ||
4 | Switch off auxiliary heater. | Only for vehicles with code D6M (Auxiliary water heater, cab or code) or code D6N (Auxiliary water heater, cab and engine). | |
5 | Provide filling unit. | ||
| 000 588 02 82 00 Filling unit | ||
Capture coolant only with the filling unit. The coolant will be cleaned through a filter during filling. | |||
6 | Open drain screw (3) and drain coolant from the radiator (2). | ||
7 | Tilt cab. | ||
8 | Remove left soundproofing from the engine. | ||
9 | Attach drain hose to the coolant drain fitting (5). | Use a commercially available hose as a drain hose. | |
10 | Open coolant drain fitting (5) and drain coolant from the engine. | ||
11 | Remove drain screws (6, 8) and drain coolant from the retarder (7). | Only on vehicles with code B3H (Secondary Water Retarder) | |
| Connection fitting for coolant return line on retarder modified | ||
12 | Switch off ignition. | ||
13 | Tighten drain screws (6, 8) on the retarder (7). | Only on vehicles with code B3H (Secondary Water Retarder) | |
| |||
Install new sealing rings. | |||
Drain screw (with solenoid) to connection fitting for coolant return line | |||
Drain screw to retarder housing | |||
14 | Remove drain hose and tighten coolant drain fitting (5). | ENGINE 470.9Coolant drain fitting to oil/coolant module | |
ENGINE 471.9, 473.9Coolant drain fitting to crankcase | |||
15 | Attach left soundproofing to the engine. | ||
16 | Tilt back cab. | ||
17 | Tighten drain screw (3) on the radiator (2). | Drain screw to engine radiator | |
| Check | ||
18 | Check drained coolant for contamination. | In the case of strong fouling, the coolant must generally be replaced. | |
Coolant for engine 473.9Coolant | |||
Coolant for engines 470.9, 471.9Coolant | |||
If coolant is severely contaminated | |||
| |||
Deoil engine cooling system. | |||
19 | Check coolant with antifreeze tester. | Coolant for engines 470.9, 471.9Coolant | |
Coolant for engine 473.9Coolant | |||
If the antifreeze protection is too low, | |||
| |||
Correct concentration of antifreeze or replace the coolant. | |||
Filling and bleeding with vacuum-type cooling system filler | |||
20 | Pour in coolant and bleed engine cooling system. | ||
| Service Information: Changed coolant filling method | ||
Vacuum-type cooling system filler | |||
Adapter | |||
21 | Close maintenance flap. |
Engine cooling |
Number | Designation | ENGINE 470.9 in MODEL 963, 964 except CODE B3H | ENGINE 470.9 in MODEL 963, 964 with CODE B3H | ||
BF20.00-N-1001-01M | Coolant | Total filling capacity | Liter | 50,0 | 70,0 |
Anticorrosion/antifreeze agent down to –37°C | Liter | 25,0 | 35,0 | ||
Anticorrosion/antifreeze agent down to –45°C | Liter | 28,5 | 39,5 | ||
Specifications for Operating Fluids, Sheet | |||||
Specifications for Operating Fluids, Sheet | |||||
Engine cooling |
Number | Designation | ENGINE 471.9 in MODEL 963, 964 except CODE B3H | Engine 471.9 in model 963, 964 | ||
BF20.00-N-1001-01M | Coolant | Total filling capacity | Liter | 60,0 | 80,0 |
Anticorrosion/antifreeze agent down to –37°C | Liter | 30,0 | 40,0 | ||
Anticorrosion/antifreeze agent down to –45°C | Liter | 33,5 | 44,5 | ||
Specifications for Operating Fluids, Sheet | |||||
Specifications for Operating Fluids, Sheet | |||||
Engine cooling |
Number | Designation | ENGINE 473.9 in MODEL 963, 964 with CODE B3H | ENGINE 473.9 in MODEL 963, 964 except CODEB3H | ||
BF20.00-N-1001-01P | Coolant | Total filling capacity | Liter | 82 | 62 |
Anticorrosion/antifreeze agent down to –37 °C | Liter | 41 | 31 | ||
Anticorrosion/antifreeze agent down to –45°C | Liter | 46 | 34,5 | ||
Specifications for Operating Fluids, Sheet | |||||
Specifications for Operating Fluids, Sheet | |||||
001 588 00 21 00
Vacuum-type cooling system filler
001 588 00 21 01
Adapter
Viitatut asiakirjat
- ah0000n500001h Ohjeita epäpuhtauksien ja vieraiden esineiden aiheuttamien vaurioiden välttämiseksi
- ah2000n208001a Jäähdytysnestettä koskevia huomautuksia
- ah4330n000301wr Ohjeita hidastimen vaikutuksesta jäähdytysnesteeseen tai jäähdytysnesteen liettymiseen
- ah6080n000301a Ohjaamon kippaamista koskevia huomautuksia
- ar2000w114203h
- ar2000w114203h
- ar2000w1250h
- as0000z000201a Loukkaantumisvaara: Kuumat tai hehkuvat esineet voivat aiheuttaa palovammoja.
- as0000z000501a Onnettomuusvaara: Varo moottorin käydessä, ettei auto lähde liikkeelle. Loukkaantumisvaara: Varo liikkuvia ja kuumia osia moottorin käydessä ja moottoria käynnistettäessä
- as0000z000901a Loukkaantumisvaara: Varo, etteivät mekaniikan osat yllättäen liikkuessaan aiheuta vammoja.
- as2000z000101a Loukkaantumisvaara: Kuuma jäähdytysneste voi aiheuttaa palovammoja. Myrkytysvaara: Jäähdytysneste on vaarallista nieltynä.
- as4330z000201a Hengenvaara: Hidastimeen tehtävät työt aiheuttavat hengenvaaran henkilöille, joilla on sydämentahdistin
- as6080z000101a Loukkaantumisvaara: Ole varovainen, kun kippaat ohjaamoa ja kun työskentelet kipatun ohjaamon alla
- bt4330w000901wr
- si2000w0002a Muutettu jäähdytysnesteen täyttömenetelmä
- ws2000n3010b