Remove/install radiator

AR20.20-D-3865TS

Remove/install radiator

15.04.2020

Engine

651 in model 907

Modification notes

16.07.2019

Document reference replaced.

Step 5

Shown with transmission 722.9 and with code HH9 (air conditioning, controlled semi-automatically, TEMPMATIC)

1

Radiator

5

Nuts

8

Air duct segment

2

Hose

6

Cover

9

Charge air cooler

3

Condenser

7

Locks

10

Electrical connector

4

Refrigerant lines

 Warning

Risk of injury to skin and eyes suffering scalding from contact with hot coolantspray. Risk of poisoning from swallowing coolant.

Do not open cooling system unless coolant temperature is below 90 °C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers.
Wear protective gloves, protective clothing and safety glasses.

AS20.00-Z-0001-01A

 Caution

Risk of injury caused by scraping or cutting body parts on sharp vehicle parts

Always wear protective gloves when working on or near sharp and non-deburred vehicle parts.
Deburr repair panels.

AS00.00-Z-0017-01A

Topical note

Notes on avoiding damage through contamination and foreign objects

AH00.00-P-5000-01A

Topical note

Information on preventing damage to electronic components due to electrostatic discharge

AH54.00-P-0001-01A

 

Remove/install

1

Discharge air conditioning system.

Engine 651 in model 907
with code HH4 (THERMOTRONIC automatic climate control)
Engine 651 in model 907
with code HH9 (Air conditioner, automatic heater control)

AR83.30-D-1760TS

2

Remove the fan.

AR20.40-D-5614TSR

3

Remove the charge air hose upstream of the charge air cooler (9).

AR09.41-D-8621TSR

4

Remove the charge air hose downstream of the charge air cooler (9).

AR09.41-D-8625TSR

5

Remove the hose (2) from the cooler (1).

AR20.20-P-7441-01RQ

6

Remove the coolant expansion reservoir.

AR20.30-D-4949TS

7

Remove the upper hose from the coolant expansion reservoir to the cooler (1).

 Hose clamp pliers

*454589003700

8

Remove front bumper.

AR88.20-D-2000TS

9

Remove the air duct segment (8) of the charge air cooler (9).

 The air duct segment (8) is attached to the charge air cooler (9) at several points.

10

Remove the fan unit for the condenser (3).

Engine 651 in model 907
with code HH4 (THERMOTRONIC automatic climate control)
Engine 651 in model 907
with code HH9 (Air conditioner, automatic heater control)

AR83.30-D-0007TS

11

Remove the oil cooler for the automatic transmission from the condenser (3).

Engine 651 in model 907 with transmission 722.9

AR27.55-D-1000TS

12

Remove the cover (6).

Engine 651 in model 907
with code HH4 (THERMOTRONIC automatic climate control)
Engine 651 in model 907
with code HH9 (Air conditioner, automatic heater control)

13

Remove the refrigerant lines (4) from the condenser (3).

Engine 651 in model 907
with code HH4 (THERMOTRONIC automatic climate control)
Engine 651 in model 907
with code HH9 (Air conditioner, automatic heater control)



Compressor oils (specification 362.1)

BB00.40-P-0362-01A

 To do so, remove nuts (5).
Seal the refrigerant lines (4) and condenser (3).

 Installation: Replace sealing rings and moisten with compressor oil.

 Nut, refrigerant condenser to refrigerant line

*BA83.30-N-1007-01TS

 Record plug

*129589009100

14

Disconnect electrical connector (10).

Engine 651 in model 907
with code HH4 (THERMOTRONIC automatic climate control)
Engine 651 in model 907
with code HH9 (Air conditioner, automatic heater control)

15

Remove the cooler (1).

 For this purpose, release locks (7) and carefully push radiator (1) in direction of engine.

16

Remove the cooler (1) upward.

 Installation: Make sure that the cooler (1) is positioned correctly in guides in longitudinal members.

17

Remove hose of coolant expansion reservoir from cooler (1).

If the cooler (1) is replaced.

 Hose clamp pliers

*454589003700

18

Remove the condenser (3) from the cooler (1).

If the cooler (1) is replaced.

Engine 651 in model 907
with code HH4 (THERMOTRONIC automatic climate control)
Engine 651 in model 907
with code HH9 (Air conditioner, automatic heater control)

AR83.30-D-6540TS

19

Remove the charge air cooler (9) from the cooler (1).

If the cooler (1) is replaced.

AR09.41-D-6817TS

20

Install in the reverse order.



Check

 Warning

Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running.

Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts.

AS00.00-Z-0005-01A

21

Check for leaktightness when engine is running.

 Visual inspection only.

 Air conditioning

Number

Designation

Model 907 with engine 274, 642, 651
Model 910 with engine 651

BA83.30-N-1007-01TS

Nut, refrigerant condenser to refrigerant line

Nm

12