Vehicle with front expansion reservoir |
1 | Cap |
W20.00-1134-11
Vehicle with rear expansion reservoir |
1 | Cap |
W20.30-1023-11
2 | Engine radiator |
3 | Drain screw |
W20.20-1080-11
4 | Heat shield |
5 | Screw plug |
W20.00-1135-11
Only for vehicles with code B3H (Secondary water retarder) |
6 | Drain screw (with magnet) |
7 | Retarder |
8 | Drain screw |
W20.00-1098-11
Danger | Risk of death to implant wearers from working on retarder | As a safe distance from the retarder, a minimum distance of 100 cm is to be maintained between the retarder and the body parts of the affected person for people with implants. | |
Warning | Risk of injury. Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | |
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
Warning | Risk of injury to skin and eyes suffering scalding from contact with hot coolantspray. Risk of poisoning from swallowing coolant. | Do not open cooling system unless coolant temperature is below 90 °C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers. | |
Warning | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure with the safety strut. | |
Caution | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. | |
Topical note | Notes and information for working on engine cooling | ||
Drain off | |||
1 | Open maintenance flap | ||
2 | Unscrew cap (1) | ||
3 | Set heater to the max. heat output and switch on ignition | ||
4 | Switch off auxiliary heater | In vehicles with code D6M (Auxiliary water heater, cab) or with code D6N (Auxiliary water heater, cab and engine) only | |
5 | Make a filling unit available | ||
| 000 588 02 82 00 Filling unit | ||
Catch coolant with filling unit only. | |||
Drain at engine radiator | |||
6 | Open drain screw (3) and drain coolant on engine radiator (2) | ||
7 | Tighten drain screw (3) on engine radiator (2) | Drain screw to engine radiator | |
Drain at engine | |||
8 | Tilt cab | ||
9 | Disconnect battery ground line | ||
10 | Remove right fender liner | ||
11 | Remove heat shield (4) on ATL | ||
12 | Remove one of screw plugs (5), and drain coolant at engine | Select screw plug (5) according to accessibility. | |
13 | Tighten screw plug (5) on engine | Replace sealing ring. | |
Screw plug to crankcase | |||
14 | Attach heat shield (4) on turbocharger | Screw/bolt, heat shield to exhaust gas turbocharger and engine brake valve fitting | |
15 | Attach right fender liner | ||
16 | Connect ground cable to battery | ||
Drain at retarder | |||
17 | Remove drain screws (6, 8) and drain coolant from retarder (7) | Only for vehicles with code B3H (Secondary water retarder) | |
18 | Tighten down drain screws (6, 8) on retarder (7) | Only for vehicles with code B3H (Secondary water retarder) | |
| |||
Replace sealing rings. | |||
Drain screw to retarder housing | |||
Drain screw to retarder coolant connection | |||
| Check | ||
19 | Check drained off coolant for contamination | In the case of strong fouling, the coolant must generally be replaced. | |
Coolant | |||
If the coolant is dirt-laden too strongly. | |||
| |||
De-oil engine cooling system. | |||
20 | Check coolant with antifreeze tester | Coolant | |
When antifreeze protection is too low. | |||
| |||
Correct concentration of antifreeze or replace coolant. | |||
Pour in | |||
21 | Fill in coolant up to lower edge of filler neck with filling unit | ||
22 | Switch on ignition, and select 4th brake stage of retarder (7) | Only for vehicles with code B3H (Secondary water retarder) | |
| |||
Retarder (7) is flooded by switching on 4th brake stage. | |||
23 | Switch off retarder (7) | Only for vehicles with code B3H (Secondary water retarder) | |
24 | Start engine, and bleed engine cooling system | Allow engine to run for approx. 5 min at changing rotational speeds. | |
25 | Screw down cap (1) | ||
26 | Turn off engine | ||
| Check | ||
27 | Check engine cooling system for leaktightness | Visual inspection. | |
28 | Tilt back cab | ||
29 | Close maintenance flap |
Coolant |
Number | Designation | Engine 460.9 in model 963, 964 | Engine 460.9 in model 963, 964 | ||
BF20.00-N-1001-01OA | Coolant | Total filling capacity | Liter | 35,0 | 50,0 |
Anticorrosion and antifreeze agent down to -37 °C | Liter | 17,5 | 25,0 | ||
Anticorrosion and antifreeze agent down to -45 °C | Liter | 20,0 | 28,5 | ||
Sheet | |||||
Sheet | |||||
Verwezen documenten
- ah2000n000101b Aanwijzingen en informatie met betrekking tot werkzaamheden aan motorkoeling
- ar2000w1250h
- ar5410w0003h
- ar8810w130001o
- as0000z000201a Kans op letsel aan huid en ogen door het omgaan met hete of gloeiende voorwerpen.
- as0000z000501a Kans op ongevallen door spontaan wegrijden bij draaiende motor. Kans op letsel door bekneld raken en verbranding bij ingrepen tijdens het starten of bij draaiende motor.
- as0000z001701a Kans op letsel. Scherpe randen van delen van de wagen kunnen snij- of schaafwonden veroorzaken.
- as2000z000101a Kans op letsel aan huid en ogen als gevolg van verbranden aan naar buiten spuitend, heet koelmiddel. Vergiftigingsgevaar door het binnenkrijgen van koelmiddel.
- as4330z000201a Voor personen met elektronische implantaten is het uitvoeren van werkzaamheden aan de retarder levensgevaarlijk.
- as6080z000101a Kans op letsel door bekneld raken bij het kantelen van de cabine.
- ws2000n3010b