Engine | 111.979/984 in model 901, 902, 903, 904 |
Engine | 601.943, 602.980 in model 901, 902, 903, 904 |
Engine | 602.984/985 in model 667, 668, 670 |
Engine | 611.981/987 in model 901, 902, 903, 904 |
Engine | 611.983 in model 690.6, 903.6, 904.6 |
Engine | 612.981 in model 902, 903, 904, 905 |
Engine | 647.981 in model 903.61/66/67, 904.61/66 |
with code ZU7 (National version for Canada) | |
Engine | 647.981 in model 903.61/66/67, 904.61/66 |
with code ZU8 (National version for USA) | |
Engine | 647.981 in model 903.61/66/67, 904.61/66 |
with code ZU9 (National version for Mexico) |
1 | Oil dipstick |
2 | Cap |
3 | Oil filter screw cap |
4 | Oil filter element |
5 | Sealing ring |
N18.00-0295-06
1 | Oil dipstick |
2 | Cap |
3 | Oil filter screw cap |
4 | Oil filter element |
5 | Sealing ring |
6 | Oil drain screw |
N18.00-2095-05
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
1 | Replace oil filter element (4) |
| |
Engine 601, 602, 611, 647 | |||
Engine 111Oil filter threaded cap | |||
Engine 601, 602, 647Oil filter threaded cap | |||
Engine 611, 612Threaded cap to oil filter | |||
Motor 601, 602 | |||
Motor 111, 611, 612, 647 | |||
2.1 | Remove bottom part of soundproofing | Model 901, 902, 903, 904, 905 except 901.6, 902.6, 903.6, 904.6 model 667, 668, 670 model 690.6 | |
| Model 901.6, 902.6, 903.6, 904.6 | ||
When draining engine oil from drain screw (6). | |||
2.2 | Remove engine compartment paneling | Only on engine 111.979/984 in model 901, 902, 903, 904 | |
When draining engine oil from drain screw (6). | |||
3 | Remove cap (2) | ||
4.1 | Remove drain screw (6) of oil pan and drain engine oil | Drain engine oil | |
Only drain engine oil when engine is at normal operating temperature. | |||
4.2 | Pull oil dipstick (1) or stop plug out of oil dipstick tube and extract engine oil | Suction off engine oil | |
Extract engine oil only when the engine is at normal operating temperature. Observe operator's manual of engine oil extractor. | |||
5.1 | Tighten drain screw (6) of oil pan | Drain engine oil | |
Replace sealing ring for drain screw (6). | |||
Engine 111Oil drain screw to oil pan | |||
Engine 601, 602, 611., 612, 647Oil drain screw to oil pan | |||
5.2 | Insert oil dipstick (1) or stop plug into oil dipstick tube | Suction off engine oil | |
Only if the engine oil was extracted through the oil dipstick tube. | |||
6 | Pour in the specified filling capacity of engine oil at the oil filler opening | ||
Notes on engine oil | Motor 111.9, 602.9, 612.9 | ||
Engine 111Engine oil | |||
Engine 601, 602, 611., 612, 647Engine oil | |||
7 | Install end cover (2) | ||
| Check | ||
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
8 | Start the engine, allow to idle for 1 to 2 minutes at idle speed and then switch off the engine | Observe oil pressure indicator. It must indicate the oil pressure after a few seconds. Do not rev up engine as long as no oil pressure is indicated. | |
9 | Check/correct oil level after a waiting time of approx. 5 min | The waiting time of 5 min must be maintained. | |
Check oil level at oil dipstick: | |||
| |||
For engines 601, 602, 611, 612, the markings on the oil dipstick (1) are designed for an engine oil temperature of approx. 80 °C. At lower engine oil temperatures after refilling the specified oil quantity, do not refill any more engine oil, even if an oil level below the maximum marking is shown. | |||
10 | Check oil filter screw cover (3) and drain screw (6) for leak tightness | ||
11.1 | Install bottom part of soundproofing | Model 901.6, 902.6, 903.6, 904.6 | |
| |||
Only if the engine oil was drained at the drain screw (6). | |||
11.2 | Install engine compartment paneling | Only on engine 111.979/984 in model 901, 902, 903, 904 | |
Only if the engine oil was drained at the drain screw (6). |
606 589 01 09 00
Socket wrench bit
103 589 02 09 00
Wrench socket