Remove/install detachable parts for replacing lower part of door frame paneling

AR60.00-D-0050TS

Remove/install detachable parts for replacing lower part of door frame paneling

14.04.2020

Model

907.6/7, 910.6

with code T16 (Sliding door right)

Right side of vehicle

Model

907.6/7, 910.6

with code T19 (Sliding door left)

Left side of vehicle

Modification notes

19.12.2019

Method extended

Operation step 7

Shown on model 910.6 with code T16 (right sliding door), right side of vehicle

Shown on model 907 with code T19 (left sliding door), left side of vehicle

2

Frame seal

3

Frame seal

4

Guide bearing

5

Bolts

Shown on model 907 with code T16 (right sliding door), right side of vehicle

17

Electrical wiring harness

 Danger

Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC)

Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines.Typ 910.6 mit Motor 780.703

AS00.00-Z-0035-01A

 Danger

Risk of death caused by vehicle slipping or toppling off of the lifting platform.

Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.

AS00.00-Z-0010-01A

Topical note

Notes on battery

Typ 910.6 mit Motor 780.703

AH54.10-P-0001-01A

Topical note

Notes on carrying out repair work in the vehicle interior

AH68.00-N-0001-01S

 

Remove/install

1

Remove respective hinge of front door.

AR72.10-D-2662TS

2

Remove respective front door sill trim.

AR68.30-D-1306TS

3

Remove respective trim from sliding door entrance.

Model 907.6 except code V39 (Plastic floor for people mover) except code VK8 (Plastic floor covering)

AR68.30-D-0018TSB

4

Remove respective bottom guide rail for the sliding door.

Model 907.6/7

AR72.16-D-7816TS

5

Remove fuel filler flap.

If left side of vehicle is damaged.

AR88.60-D-6023TS

6

Remove respective underfloor paneling.

Model 907.6/7 with code XM1 (Noise abatement measures), model 910.6 with engine 651 with code XM1 (Noise abatement measures), model 910.6 with engine 780.703

AR61.30-D-1001TS

7

Remove respective underfloor paneling at high-voltage battery carrier.

* Applies to Europe only

Model 910.6 with engine 780.703

AR61.30-D-1002TE

8

Remove filler neck.

If left side of vehicle is damaged.

Model 907.6 with engine 654.9, Models 907.6/7 with engines 642, 651, Model 910.6 with engine 651

AR47.10-D-7541TS

Model 907.6/7 with engine 274

AR47.10-D-7541TSC

9

Remove lower trim from partition.

Model 907.6, 910.6 with partition wall and with code VA3 (load compartment interior trim up to roof height, washable)

AR68.30-D-1408TS

10

Remove respective sealing frame (2) in the repair area and position outside the working area.

11

Remove respective sealing frame (3) in the repair area and position outside the working area.

12

Remove respective front fender.

AR88.10-D-1005TS

13

Remove respective lower front fender.

AR88.10-D-0002TS

14

Remove each front wheel.

AR40.10-D-1100TS

15

Remove respective rear section of front fender liner.

AR88.10-D-1321TS

16

Remove respective protective strip.

AR88.80-D-1040TS

17

Remove respective electrical wiring harness (17) in the repair area and position outside the working area.

18

Remove guide bearings (4).

 To do this, remove the screw/bolts (5).

 Striker pin to B-pillar

*BA72.16-N-1005-01TS

19

Remove respective front floor covering.

Model 907.6/7

AR68.80-D-0006TSR

Model 910.6

AR68.80-D-0006TSF

20

Remove respective seat belt from B-pillar.

AR91.40-D-1015TS

21

Install in the reverse order.

 Sliding door

Number

Designation

Model 907.6/7/8, 910.6

BA72.16-N-1005-01TS

Striker pin to B-pillar

Nm

30