Remove/install detachable parts for replacing rear crossmember paneling and one lower part of the rear corner pillar paneling

AR60.00-D-0046TS

Remove/install detachable parts for replacing rear crossmember paneling and one lower part of the rear corner pillar paneling

15.01.2020

Model

907.6/7, 910.6

Shown on model 907.6

1

Rear crossmember paneling

Shown on model 907.6, right side of vehicle

10

Corner pillar paneling lower part

Shown on model 907 with code Q50 (Removable ball head for trailer coupling)

2

Rear-end doors

5

Frame seal

7

Right guide pin

3

Bumper

6

Left lock striker

8

Cover

4

Trailer hitch

Shown on model 907 with code Q50 (Removable ball head for trailer coupling)

4

Trailer hitch

9

Electrical wiring harness

Shown on model 907 with code P48 (Rear mud flap), left side of the vehicle

11

Protective strip

12

Passage grommet

13

Plug

14

Connector

15

Dirt trap

16

Screws

17

Nuts

 Danger

Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC)

Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines.Model 910.6 with engine 780.703

AS00.00-Z-0035-01A

 Danger

Risk of death caused by vehicle slipping or toppling off of the lifting platform.

Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.

AS00.00-Z-0010-01A

 Warning

Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.

No parts of the body or limbs should be within the operating area when the components are moving.

AS00.00-Z-0011-01A

Topical note

General information on vehicles with high-voltage on-board electrical system and/or lithium-ion battery and/or gaseous-fuel drive system as well as personal protective equipment

Model 910.6 with engine 780.703

AH00.00-Z-0300-01A

Topical note

Notes on carrying out repair work in the vehicle interior

AH68.00-N-0001-01S

 

Remove/install

1

Remove respective wheel well trim.

Model 907.6, 910.6
with code V52 (Load-supporting wheel well)

AR68.30-D-0016TS

2

Remove respective rear load compartment trim at the side.

Model 907.6, 910.6
with code V25 (Basic panelling in load compart. up to belt rail)
Model 907.6, 910.6
with code VA1 (Panelling in load comp. up to belt rail standard)
Model 907.6, 910.6
with code VA2 (Load space int. trim up to roof (wood))
Model 907.6, 910.6
with code VA3 (Interior trim, cargo bay to roof height, washable)

AR68.30-D-1185TS

3

Remove respective rear side wall trim in passenger compartment.

Model 907.6
with code V21 (Interior panelling luxury)
Model 907.7

AR68.30-D-1208TSR

4

Remove tie-down rail from side wall.

Model 907.6, 910.6
with code V42 (Sidewall tie-down rails on waist rail)

AR68.50-D-8250TS

5

Remove sealing frame (5) in repair area and position outside the working area.

6

Remove cover (8) for rear entrance.

AR68.30-D-3520TS

 In the process, the left lock striker (6) and the right guide pin (7) are removed.

7

Remove rear bumper (3).

Model 907.6/7, 910.6
with code JA7 (Blind Spot Monitoring)
Model 907.6/7, 910.6
with code JB6 (Parking package with 360-degree camera)
Model 907.6/7, 910.6
with code JB7 (Parking Package with reversing camera)

AR88.20-D-2200TS

Model 907.6/7, 910.6
except code JA7 (Blind Spot Monitoring)
except code JB6 (Parking package with 360-degree camera)
except code JB7 (Parking Package with reversing camera)

AR88.20-D-2200TSB

8.1

Remove sprung step.

Model 907.6/7, 910.6
with code W76 (Rear step sprung)

 To do so, counterhold nuts and remove screws of the sprung step.

 Helper required.

 Screw/nut, sprung running board to longitudinal member

*BA88.30-N-1001-03TS

8.2

Remove step.

Model 907.6/7, 910.6
with code W75 (Step, wide, at rear end)

 To do so, counterhold nuts and remove screws of the step.

 Helper required.

 Screw/nut, running board to longitudinal member

*BA88.30-N-1004-03TS

9

Remove trailer hitch (4).

Model 907.6/7, 910.6
with code Q20 (Trailer hitch (jaw-type))
Model 907.6/7, 910.6
with code Q22 (Trailer coupling, rigid coupling head)
Model 907.6/7, 910.6
with code Q24 (Trailer cross member NAFTA, towing capacity 5000Ibs)
Model 907.6/7, 910.6
with code Q50 (Trailer coupling with removable ball-type head)
Model 907.6/7, 910.6
with code QA7 (Trailer hitch for increased towing capacity 3.5 t)
Model 907.6/7, 910.6
with code QA8 (Trailer hitch for increased towing capacity 2.8 t/3.0 t)

AR31.10-D-8000TS

10

Remove spare wheel holder under frame end.

Model 907.6/7, 910.6
with code R65 (Spare wheel bracket below frame end)

Topical note

Notes on self-locking nuts and bolts

AH00.00-N-0001-01A

 For this purpose, remove nuts.

11

Remove respective protective strip (11).

AR88.80-D-1040TS

12

Remove respective feed-through grommet (12).

Model 907.6/7, 910.6
with code LB1 (Side marker lights)

 To do so, position connector (14) with feed-through grommet (12) outside the working area in the vehicle interior.

13

Remove respective plugs (13).

 The number of plugs (13) may vary depending on the body length.

14

Remove rear-end doors (2).

AR72.20-D-1901TS

15

Remove electrical wiring harness (9) and position outside the working area.

16

Remove respective rear lamp unit.

AR82.10-D-4731TS

17

Remove vent flap from the respective lower part of corner pillar paneling (10).

18

Install in the reverse order.

 Running boards

Number

Designation

Model 907, 910

BA88.30-N-1001-03TS

Screw/nut, sprung running board to longitudinal member

Nm

94

 Running boards

Number

Designation

Model 907, 910

BA88.30-N-1004-03TS

Screw/nut, running board to longitudinal member

Nm

94