Vehicle with front expansion reservoir |
1 | Cap |
W20.30-1022-11
Vehicle with rear expansion reservoir |
1 | Cap |
W20.30-1023-11
2 | Engine radiator |
3 | Drain screw |
W20.20-1080-11
Vehicle with code B3H (Secondary-water-retarder) |
6 | Drain screw (with magnet) |
7 | Retarder |
8 | Drain screw |
W20.00-1098-11
Warning | Risk of injury. Moving parts can pinch, crush or, in extreme cases even sever extremities. | No parts of the body or limbs should be within the operating area of mechanical components when moving components. | |
Warning | Risk of injury. Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | |
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
Danger | Risk of death to implant wearers from working on retarder | As a safe distance from the retarder, a minimum distance of 100 cm is to be maintained between the retarder and the body parts of the affected person for people with implants.Nur bei Fahrzeugen mit Code B3H (Sekundär-Wasser-Retarder). | |
Warning | Risk of injury to skin and eyes suffering scalding from contact with hot coolantspray. Risk of poisoning from swallowing coolant. | Do not open cooling system unless coolant temperature is below 90 °C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers. | |
Topical note | Notes on avoiding damage through contamination and foreign objects | ||
Topical note | Notes on influence of retarder on coolant/coolant sludging | Nur bei Fahrzeugen mit Code B3H (Sekundär-Wasser-Retarder). | |
Topical note | Notes on coolant | ||
Drain off | |||
1 | Open maintenance flap. | ||
2 | Unscrew cap (1). | ||
3 | Set heating to max. heating output and switch on ignition. | ||
4 | Switch off auxiliary heater. | Only for vehicles with code D6M (Auxiliary water heater, cab or code) or code D6N (Auxiliary water heater, cab and engine). | |
5 | Provide filling unit. | ||
| 000 588 02 82 00 Filling unit | ||
Capture coolant only with the filling unit. The coolant will be cleaned through a filter during filling. | |||
6 | Open drain screw (3) and drain coolant from the radiator (2). | ||
7 | Remove drain screws (6, 8) and drain coolant from the retarder (7). | Only on vehicles with code B3H (Secondary Water Retarder) | |
| Connection fitting for coolant return line on retarder modified | ||
8 | Switch off ignition. | ||
9 | Tighten drain screws (6, 8) on the retarder (7). | Only on vehicles with code B3H (Secondary Water Retarder) | |
| |||
Install new sealing rings. | |||
Drain screw (with solenoid) to connection fitting for coolant return line | |||
Drain screw to retarder housing | |||
10 | Tighten drain screw (3) at radiator (2). | Drain screw to engine radiator | |
| Check | ||
11 | Check drained coolant for contamination. | In the case of strong fouling, the coolant must generally be replaced. | |
Coolant | |||
If the coolant is severely contaminated, | |||
| |||
Deoil engine cooling system. | |||
12 | Check coolant with antifreeze tester. | Coolant | |
If the antifreeze protection is too low, | |||
| |||
Correct concentration of antifreeze or replace the coolant. | |||
Filling and bleeding with vacuum-type cooling system filler | |||
13 | Pour in coolant and bleed engine cooling system. | ||
| Service Information: Changed coolant filling method | ||
Vacuum-type cooling system filler | |||
Adapter | |||
14 | Close maintenance flap. |
Engine cooling |
Number | Designation | Engine 936.9 in model 963, 964 | Engine 936.9 in model 963, 964 | ||
BF20.00-N-1001-01N | Coolant | Total filling capacity | Liter | 40,0 | 60,0 |
Anticorrosion and antifreeze agent down to -37 °C | Liter | 20,0 | 30,0 | ||
Anticorrosion and antifreeze agent down to -45 °C | Liter | 22,5 | 33,5 | ||
Sheet | |||||
Sheet | |||||
001 588 00 21 00
Vacuum-type cooling system filler
001 588 00 21 01
Adapter
参照文書
- ah0000n500001h 汚れおよび異物による損傷防止に関する注意事項
- ah2000n208001a クーラントについての注意事項
- ah4330n000301wr クーラントまたはクーラント泥化へのリターダの影響 に関する注意事項
- ar2000w114203h
- ar2000w114203h
- ar2000w1250h
- as0000z000201a 高温になっているか、あるいは赤熱している部品を取り扱う場合に、火傷を負うあるいは失明する危険があります。
- as0000z000501a エンジン作動中に車両がひとりでに動き出す危険があります。 スタート時または作動中のエンジンに接触すると、巻き込まれて負傷をする、または火傷をする危険があります。
- as0000z000901a 手指をはさまれたり、締め付けられて負傷する危険があります。注意をおこたると、メカニズムに巻き込まれて、手指が切断される危険もあります。
- as2000z000101a 高温のクーラントが高圧で噴出して、皮フおよび目に火傷を負う危険があります。クーラントを誤飲すると、中毒になる危険があります。
- as4330z000201a 人工臓器を着用している人がリターダー での作業を行うことによる生命の危険
- bt4330w000901wr
- si2000w0002a
- ws2000n3010b 000 588 02 82 00 充填装置