ar2910w0300a

Remove/install pedal assembly

Typ ar · téma 29.10 · verze 0204 · 2016-08-19

Platí pro: Model 950, 952, 953, 954 with body 942.899 with code GE1 (Electronic drive control)

Není k dispozici v jazyce „cs“; zobrazeno v jazyce Angličtina.

Zařazení

Funkční skupina 2 Podvozek › 29 Pedálové ústrojí › 29.10 Pedály, konzola — Řada 942 (modely 899) · Řada 950 · Řada 952 · Řada 953 · Řada 954

EinPAS 37 Vnitřní výbava › 37.50 Pedály › 37.50.40 Držák pedálu/konzola pedálu — Řada 942 (modely 899) · Řada 950 · Řada 952 · Řada 953 · Řada 954

AR29.10-W-0300A

Remove/install pedal assembly

16.08.2016

Model

950, 952, 953, 954 with body 942.899

with code GE1 (Electronic drive control)

Remove/install pedal assembly

W29.10-0001-09

1

Pedal bracket

5

Master cylinder

10

Cable

2

Remove washers

6

Expansion reservoir

B44

Brake value sensor

3

Bolts

8

Wiper linkage

4

Nuts

9

Electrical line

Danger !

Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running.

Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts.

AS00.00-Z-0005-01A

Notes on compressed air connection systems

AH00.18-N-0001-01A

Remove/install

1

Switch off ignition

2

Open maintenance flap

3

Discharge compressed-air system

4

Pull master cylinder (5) with attached hydraulic line out of pedal bracket (1) and tie to one side

AR25.20-W-0100A

Do not detach hydraulic line from master cylinder (5).

5

Detach compressed air lines from brake value sensor (B44)


With "VOSS 230" compressed air connector

AR42.10-W-0900A

With VOSS "232" or SCHÄFER "SDF" compressed air connector

AR42.10-W-0900C

Mark installation position.

Installation: Check O-rings and replace if necessary. Observe identification of compressed air lines.

6.1

Detach electrical connections from brake light switch

Vehicles without code BB8 (Brake control (BS) with ASR)

AR42.10-W-0040A

6.2

Detach electrical connections from brake value sensor (B44)

Vehicles with code BB8 (Brake control (BS) with ASR)

7

Detach electrical connections from microswitch on emergency clutch pedal

AR29.10-W-0380A

8

Detach Bowden cable for releasing emergency clutch pedal.

AR29.10-W-0370A

9

Detach wiper linkage (8) and flip downwards

10

Unhook wire (10) from locks of maintenance flap lock

11

Unhook wire (10) from operating lever of maintenance flap

Pull out wire (10) forwards through the mounting hole in the pedal bracket (1) and place to one side.

12

Detach connector from electrical line (9) on instrument cluster

The connector of the electrical line (9) for the tachograph sensor can be accessed through the footwell on the driver side.

13

Expose electrical line (9)

Pull out electrical line (9) together with rubber grommet forwards through the mounting hole in the pedal bracket (1) and place to one side.

Installation: Check rubber grommet is correctly seated in mounting hole.

14

Remove pedal bracket (1)

Installation: Check seal on pedal bracket (1) for damage, replace if necessary.

Pedal bracket to firewall

*BA29.10-N-1001-02A

15

Install in the reverse order

16

Adjust brake pedal

AR29.10-W-0080A

17

Start engine and completely inflate air brake system with idle speed

18

Switch off ignition

19

Check compressed air lines on brake value sensor (B44) for leaktightness

Leak detection spray

*BR00.45-Z-1002-03A

Pedals, bearing bracket, pedal bracket

Number

Designation

Model 374.5/6, 375.3/4, 940, 942, 943, 944, 950, 952, 953, 954, 958.2/4

BA29.10-N-1001-02A

Pedal bracket to firewall

Nm

25

Repair materials

Number

Designation

Order number

BR00.45-Z-1002-03A

Leak detection spray

Christof Fischer GmbH
www.kaeltefischer.de

Odkazované dokumenty