1 | Locking pin |
2 | Plug |
3 | Oil dipstick |
A | Measuring marks 9.5 and 11 |
B | Measuring marks 3.5 and 5 |
D27.00-1113-06
Warning | Risk of burns and scalding when handling hot fluids and components they come into contact with. Risk of injury to skin and eyes when handling hot fluids. | Wear protective gloves, protective clothing and safety glasses, if necessary. Pour hot fluids in suitable containers only. | |
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
Notes on automatic transmission | |||
| Check | ||
1 | Park vehicle. | | |
2 | Remove locking pin (1). | Break off the plate of the locking pin (1) using a screwdriver and push out the pin remaining in the plug (2) in a downward direction. | |
3 | Remove plug (2). | ||
4 | Pour in transmission oil via guide tube. | After opening transmission oil circuit or after replacing or repairing automatic transmission. | |
| Automatic transmission fluids (ATF) (specification 236.15) | ||
| |||
Automatic transmission fluid ATF | |||
Funnel | |||
After replacement of automatic transmission | |||
| |||
Pour in 10 l of transmission oil. | |||
After opening oil circuit or repairing automatic transmission | |||
| |||
Pour in quantity of transmission oil drained previously plus an additional 0.5 l of transmission oil. | |||
5 | Connect vehicle diagnosis system and check transmission oil temperature. | ||
| |||
| |||
6 | Heat up transmission oil to 90 °C (194 °F). | After opening transmission oil circuit. | |
Shift the automatic transmission to selector lever position "P" and keep the engine speed at 2500 rpm. | |||
The thermostat of the automatic transmission oil cooler opens at 90 °C (194 °F), and the automatic transmission oil cooler is filled and bled. | |||
7 | Allow transmission oil to heat up or cool down to 35 °C (95 °F) or 75 °C (167 °F). | To heat up transmission oil | |
| |||
Shift the automatic transmission to selector lever position "P" and keep the engine speed at 2500 rpm. | |||
To cool down transmission oil | |||
| |||
Switch off engine. | |||
8 | Check transmission oil temperature. | | |
9 | Start engine. | Leave the automatic transmission at selector lever position "P" and the engine running at idle speed. | |
10 | Insert oil dipstick (3) into oil dipstick tube up to end stop, pull out and read off oil level. | ||
| Automatic transmission fluids (ATF) (specification 236.15) | ||
| |||
| |||
At a transmission oil temperature of 35 °C (95 °F), the oil level must be between the measuring marks 3.5 and 5 (B). At a transmission oil temperature of 75 °C (167 °F), the oil level must be between the measuring marks 9.5 and 11 (A). | |||
Automatic transmission fluid ATF | |||
Hand pump | |||
Funnel | |||
Dipstick | |||
Oil level too low | |||
| |||
Pour in transmission oil via guide tube. | |||
Oil level too high | |||
| |||
Extract transmission oil via guide tube. | |||
11 | Repeat procedure starting with operation step 8. | After pouring in or extracting transmission oil. | |
12 | Switch off engine. | ||
13 | Disconnect diagnostic system. | ||
| |||
14 | Fit plug (2) to filler pipe. | Check sealing ring on plug (2) for damage and replace if necessary. | |
15 | Install new locking pin (1) in plug (2). |
Automatic transmission |
Number | Designation | Transmission 722.9 | |||
BF27.00-N-1001-01A | Automatic transmission fluid ATF | Filling capacity - complete refill | Liter | 10,0 | |
Filling capacity - oil change | Liter | 9,0 | |||
Filling capacity, transmission oil change | with torque converter | Liter | 9,0 | ||
Filling capacity, transmission oil change | without torque converter | Liter | 5,5 | ||
Sheet | |||||
Sheet | - | ||||
Sheet | - | ||||
Sheet | - | ||||
Sheet | - | ||||
210 589 00 71 00
Hand pump
126 589 12 63 00
Funnel
722 589 00 21 00
Dipstick