Inspect cooling system for leaks · ar2000p1010fh · Mercedes-Benz WIS

AR20.00-P-1010FH

Inspect cooling system for leaks

24.5.11

ENGINES 276 in MODEL 204

ENGINES 276, 278 in MODEL 207

P20.00-2421-05

1 Cap

2 Coolant expansion reservoir

3 Tester cap

4 Pressure pump

	Removing
 Danger!	Risk of injury caused by fingers being pinched or crushed when removing, installing or aligning hoods, doors, trunk lids, liftgates or sliding roof	Keep body parts and limbs well clear of moving parts.	AS00.00-Z-0011-01A
 Danger!	Risk of injury to skin and eyes caused by scalding from contact with hot coolant spray. Risk of poisoning caused by swallowing coolant.	Do not open cooling system unless coolant temperature is below 90°C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers. Wear protective gloves, protective clothing and safety glasses.	AS20.00-Z-0001-01A
1	Switch on ignition
2	Adjust heater to maximum heat output
3	Unscrew cap (1) from coolant expansion reservoir (2)	 Unscrew cap (1) slowly and relieve excess pressure.
4	Check coolant level and antifreeze content coolant	 If antifreeze content of coolant is too small, either antifreeze must be added or the coolant must be replaced.
5	Screw on test cap (3) at coolant expansion reservoir (2)		*210589009100
6	Connect pressure pump (4) at test cap (3)		*124589242100
7	Apply test pressure to cooling system	 To prevent damage to cooling system, do not exceed stated test pressure.	*BE20.30-P-1005-01A
	Checking
8	Perform visual inspection on coolant carrying components	 Check condition and coolant loss for all coolant carrying components and connections. The coolant carrying components should be checked for inner leaktightness if there is no external coolant loss. There is the possibility, for example, that coolant can find its way over a defective cylinder head gasket into the combustion chamber or over a defective water heat exchanger into the oil circuits.
		 Check condition and seating of the Henn coupling; replace catch springs as required in order to avoid coolant loss.
		See Open and close Henn coupling.	AR09.41-P-1311-01AL
	Install
9	Relieve test pressure in cooling system	 To do this actuate pressure relief button on the pressure pump (4)
10	Detach pressure pump (4) from tester cap (3)
11	Unscrew test cap (3) on coolant expansion reservoir (2)
12	Switch off ignition
13	Check coolant level and antifreeze content coolant	 Mixture ratio for coolant	*BF20.00-P-1001-04A
	Notes on coolant level		AH20.00-P-1142-01CW
14	Screw screw cap onto coolant expansion reservoir (2)

Cap for radiator or expansion reservoir

Number	Designation		2-stage cap


BE20.30-P-1005-01A	Test pressure for pressure-testing cooling system	bar gage	1.4

 Mixture ratio for coolant

Number	Designation			ENGINE all


BF20.00-P-1001-04A	Mixture ratio for coolant	Antifreeze/water	up to -37°C	50/50
			up to -45°C	55/45
		Specifications for service products	Sheet	BB00.40-P-0310-01A
			Sheet	BB00.40-P-0325-00A

124 589 24 21 00

Pressure pump

Test cap

210 589 00 91 00

Documente menționate

ah2000p114201cw Indicaţii pentru nivelul lichidului de răcire
ar0941p131101al Decuplaţi şi cuplaţi ambreiajul
as0000z001101a Pericol de rănire prin prinderea sau strivirea degetelor la operaţii de demontare, montare şi reglare la capote, uşi, capace şi tavan culisant
as2000z000101a Pericol de rănire la piele şi ochi prin opărire cu lichid de răcire fierbinte pulverizat afară. Pericol de otrăvire datorită înghiţirii lichid de răcire.