7 | Digital tachograph (DTCO) 2nd generation |
8 | Lead seal |
9 | Battery compartment |
D54.61-A019-04
2 | Cover |
3 | Cover |
D54.61-1177-06
5 | Equipment installation frame |
6 | Frame |
D54.61-A004-06
Caution | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. | |
Topical note | Notes on carrying out repair work in the vehicle interior | ||
Topical note | Information on preventing damage to electronic components due to electrostatic discharge | ||
| Check | ||
1 | Check delivery condition of 2nd generation DTCO (7). | The information regarding manufacturer, device type and serial number on the model plate must correspond to the information on the delivery note. The lead seal of the 2nd generation DTCO (7), and the lead seal (8) of the battery compartment (9) must be intact. | |
If the lead seal of the 2nd generation DTCO (7) or lead seal (8) of the battery compartment (9) is damaged or the specifications for the manufacturer, device type and serial number do not match the delivery note, | |||
| |||
order new 2nd generation DTCO (7) and return faulty 2nd generation DTCO (7). | |||
| Remove | ||
2.1 | Remove cover (2). | Model 907, 910 with code H1B (Operation of front tachograph under headliner) | |
Cover (2) is no longer required and must be handed over to the customer or disposed of properly following consultation with the customer. | |||
2.2 | Remove cover (3). | Model 907, 910 with code J2B (Operation of front tachograph under instrument panel, front passenger side) | |
Cover (3) is no longer required and must be handed over to the customer or disposed of properly following consultation with the customer. | |||
| Install | ||
3 | Install device installation frame (5). | To do so, insert device installation frame (5) into frame (6) and bend over shackles (arrows) until device installation frame (5) can no longer be moved. | |
Model 907, 910 with code H1B (Operation of front tachograph under headliner) | |||
Model 907, 910 with code J2B (Operation of front tachograph under instrument panel, front passenger side) | |||
4 | Subsequently connect and install 2nd generation DTCO (7). | ||
5 | Enter special equipment into on-line vehicle data card. | Designation of affected special equipment: Code JD6 (EU intelligent tachograph). | |
Delete existing code J4V (Pre-installation for EU intelligent tachograph). | |||
Attach "Digital tachograph retrofitted as per AN54.61-D-2002TS" note under field organization texts to DG 54. | |||
6 | Carry out SCN coding on electronic ignition lock control unit (EZS). | ||
| |||
Do not yet remove vehicle diagnosis system. | |||
7 | Carry out SCN coding on instrument cluster (IC) control unit. | ||
| |||
8 | Enter serial numbers of 2nd generation DTCO (7), rpm sensor and lead seal of rpm sensor into Vehicle Documentation (VeDoc). | ||
9 | Tachograph inspection to be carried out by authorized personnel. | When doing so, observe operator's manual included with 2nd generation DTCO (7). | |
Observe national legal requirements for tachograph testing. In the Federal Republic of Germany, perform the tachograph inspection as per Art. 57b of the German Regulations Authorizing the Use of Vehicles for Road Traffic (StVZO). | |||
10 | Place operator's manual of 2nd generation DTCO (7) in vehicle. |
Referenced documents
- ah5400p000101a Information on preventing damage to electronic components due to electrostatic discharge
- ah6800n000101s Notes on carrying out repair work in the vehicle interior
- an5461d200204ts Subsequently connect and install digital tachograph (DTCO), 2nd generation
- ar5421d0015ts SCN coding of control units
- as0000z001701a Risk of injury caused by scraping or cutting body parts on sharp vehicle parts