P09.20-2188-09
1 Intake manifold
2 Seals
3 Fuel pipe
Y22/6 Variable intake manifold switchover valve
Arrow: Bore for combination valve
4 Exhaust gas recirculation valve
5 Union nut
6 Combination valve
| Remove/install | ||
Danger! | Risk of explosion caused by fuel igniting, risk of poisoning caused by inhaling and swallowing fuel as well as risk of injury to eyes and skin caused by contact with fuel. | No fire, sparks, open flames or smoking. Wear protective clothing when handling fuel. | |
Danger! | Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | When moving components, ensure that no body parts or limbs are within operating range of moving parts. | |
1 | Switch ignition off and remove ignition key (transmitter key). | On vehicles with code 889 Keyless Go: Press Keyless Go start/stop button repeatedly until the ignition is switched off. Remove transmitter key from vehicle and store it in a location beyond its transmission range (at least 2 m). | |
2 | Open engine hood and raise to vertical position | ||
3 | Remove air filter housing | ||
4 | Remove hot film mass air flow sensor with air intake pipe | ||
5 | Dismount fuel line (3) from fuel distributor | | |
6 | Removing fuel rail with injection valves | ||
| |||
7 | Remove vacuum lines from intake manifold (1) and variable intake manifold switchover valve (Y22/6) | Installation: Observe intake manifold connection diagram. | |
8 | Disconnect electrical connector at variable intake manifold switchover valve (Y22/6) | ||
9 | Screw down union nut (5) on line to exhaust gas recirculation valve (4) | Counterhold connection fitting when unscrewing. | |
10 | Remove combination valves (6) | ||
11 | Remove intake manifold (1) bolts on cylinder head | | |
12 | Remove intake manifold (1) upwards | Plug intake ducts. | |
The intake manifold must not be disassembled. | |||
Installation: Replace seals (2). When mounting observe correct seating of bore for combination valve (see arrow). | |||
Installation: Use centering pin to achieve exact bottoming of intake manifold as well as centering of seals (2) . | |||
Set of dowel bolts | |||
13 | Install in the reverse order | ||
Danger! | Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near a running engine | Secure vehicle to prevent it from moving by itself. | |
14 | Carry out engine test run and check intake manifold (1) for leaks | In the event of a leak, determine and eliminate cause, otherwise malfunctions and serious environmental pollution may occur. |
Fuel rail
Number | Designation | Engines | |
BA07.52-P-1001-01A | Disconnect fuel feed line at fuel rail | Nm | 38 |
BA07.52-P-1002-01A | Bolt, fuel rail to intake manifold | Nm | 10 |
Intake manifold
Number | Designation | Engines | ||
BA09.20-P-1001-01D | Bolt, intake manifold to cylinder head | M8 | Nm | 20 |
112 589 02 62 00
Set of dowel bolts
Henviste dokumenter
- ar0703p1451rt
- ar0707p1454rt
- ar0910p1150rt
- ar0910p1150rtb
- ar0910p1150rtc
- ar0920p131001gz
- ar8840p1000rt
- as0000z000501a Fare for ulykke ved automatisk igangsætning når motoren kører. Fare for personskade på grund af knusning og forbrænding, hvis der arbejdes mens motoren startes eller kører
- as0000z001101a Fare for personskade pga. fastklemning eller knusning af fingre ved af-, påmontering og indstillingsarbejde på motorhjelm og bagklap, døre, dæksler og soltag.
- as4700z000101a Fare for eksplosion ved tænding, fare for forgiftning ved indånding og indtagelse af brændstof samt fare for hud- og øjenskader ved kontakt med brændstof