Variant 1 is shown, 10-pin electrical connector on footrest |
1 | Electrical connector (10-pin) |
P91.60-4998-11
Variant 2 is shown, 10-pin electrical connector (X29/9) behind footrest |
X29/9 | Electrical connector (10-pin) |
P91.60-5003-11
Shown with side transmission tunnel lining removed |
2 | Screw |
P91.60-4999-11
Shown with glove compartment box insert removed |
3 | Cable tie |
P91.60-5000-11
Shown with floor covering removed |
4 | Connecting cable |
P91.60-5001-11
Shown on vehicle without center console |
2 | Bolts |
P91.60-5002-11
Shown on vehicle without center console |
N2/2 | Airbag/emergency tensioning retractor control unit |
P91.60-5004-11
Warning | Risk of injury during testing and repair operations related to pyrotechnical components | Do not expose pyrotechnical component parts to temperatures above 100 °C or 212 °F. Disconnect current supply when working on such component parts. | |
Topical note | Information on preventing damage to electronic components due to electrostatic discharge | ||
Information, assessment and legal requirements when working with, handling and storing pyrotechnical components | |||
| Remove | ||
1 | Switch off ignition and remove ignition key | ||
2 | Disconnect battery ground line | ||
3 | Remove front passenger footwell floor covering | ||
4 | Loosen nuts of footrest on front passenger footwell firewall | ||
5 | Turn footrest in footwell | ||
6.1 | Disconnect 10-pin electrical connector (1) in front passenger footwell | Variant 1, 10-pin electrical connector (1) on footrest. | |
6.2 | Disconnect 10-pin electrical connector (X29/9) in front passenger footwell | Variant 2, 10-pin electrical connector (X29/9) behind footrest. | |
7 | Remove cover below instrument panel in front passenger footwell | ||
8 | Remove glove compartment box insert | ||
9 | Remove air duct segment for right-hand side air vent | ||
10 | Remove left and right side transmission tunnel lining | ||
11 | Remove screws/bolts (2) from airbag/emergency tensioning retractor control unit (N2/2) | ||
12 | Open cable tie (3) in area of firewall | ||
13 | Fasten cord to 10-pin electrical connector (X29/9) or 10-pin electrical connector (1) of connecting cable (4) | The cord enables the new connecting cable (4) to be drawn through the front wall pillar more easily. | |
14 | Pull connecting cable (4) out of the front wall pillar | ||
15 | Remove airbag/emergency tensioning retractor control unit (N2/2) with connecting cable (4) | The arrow on the airbag/emergency tensioning retractor control unit must be pointing in the direction of travel. | |
| Install | ||
16 | Place airbag/emergency tensioning retractor control unit (N2/2) with connecting cable (4) onto mounting plate | The arrow on the airbag/emergency tensioning retractor control unit must be pointing in the direction of travel. | |
17 | Screw in screws/bolts (2) of airbag/emergency tensioning retractor control unit (N2/2) | Bolt, control unit to vehicle floor | |
18 | Connect 10-pin electrical connector (X29/9) or 10-pin electrical connector (1) to wiring harness | ||
19 | Connect ground cable to battery | ||
20 | Switch on ignition | ||
21 | SRS and RS indicator lamp must go off after approx. 10 seconds | If the SRS or RS indicator lamp does not go off after approx. 10 s. | |
| |||
Check airbag/emergency tensioning retractor system with test equipment. | |||
Tester | |||
22 | Disconnect battery ground line | ||
23 | Disconnect 10-pin electrical connector (X29/9) or 10-pin electrical connector (1) from wiring harness | ||
24 | Attach cord to 10-pin electrical connector (X29/9) or 10-pin electrical connector (1) and route the connecting cable (4) through the front wall pillar using the cord | ||
25 | Check airbag/emergency tensioning retractor system with test equipment | Tester | |
26.1 | Connect 10-pin electrical connector (1) in front passenger footwell | Variant 1, 10-pin electrical connector (1) on footrest. | |
26.2 | Connect 10-pin electrical connector (X29/9) in front passenger footwell | Variant 2, 10-pin electrical connector (X29/9) behind footrest. | |
27 | Route connecting cable (4) in area of firewall and fix in place with cable tie (3) | ||
28 | Fix cable tie (3) in place | ||
29 | Remove cord | ||
30 | Install left and right side transmission tunnel lining | ||
31 | Insert air duct segment for right-hand side air vent | ||
32 | Install glove compartment box insert | ||
33 | Install cover below instrument panel in front passenger footwell | ||
34 | Place front passenger footwell floor covering in position | ||
35 | Connect ground cable to battery | ||
| Check | ||
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
36 | Start engine, SRS/RS indicator lamp must go off after approx. 10 s | If the SRS or RS indicator lamp does not go off after approx. 10 s. | |
| |||
Check airbag/emergency tensioning retractor system with test equipment. | |||
Tester |
126 589 10 21 00
Tester
Powiązane dokumenty
- ah5400p000101a Wskazówki dotyczące zapobiegania uszkodzeniom elementów elektronicznych na skutek rozładowania potencjału elektrostatycznego
- ah9100z000010a Wskazówki, oceny i prawne przepisy dotyczące wykonywania prac, składowania i postępowania z elementami pirotechnicznymi
- as0000z000501a Niebezpieczeństwo wypadku na skutek samoczynnego ruszenia przy pracującym silniku. Niebezpieczeństwo obrażeń na skutek zmiażdżenia lub poparzenia przy wykonywaniu czynności podczas rozruchu lub przy pracującym silniku.
- as9100z000801a Niebezpieczeństwo obrażeń podczas napraw i czynności diagnostycznych związanych z elementami pirotechnicznymi