S07.04-4747-78
1 | Screw | 4 | Heat shield | 7 | Engine suspension lug on the rear right | ||
2 | Bracket | 5 | Retaining clamp | 8 | Turbocharger | ||
3 | Bolts | 6 | Bolts |
8 | Turbocharger |
9 | Electrical connector |
10 | Pressure sensor |
11 | Right rail |
S07.04-4748-81
Danger | Risk of explosion caused by fuel igniting. Risk of injury to skin and eyes caused by fuel spraying out at high pressure | Keep all ignition sources out of hazard area. | |
Danger | Risk of explosion caused by fuel igniting, risk of poisoning caused by inhaling and swallowing fuel as well as risk of injury to eyes and skin caused by contactwith fuel. | No fires, sparks, open flames or smoking. Pour fuels into suitable and appropriately marked containers only. | |
Topical note | Information on preventing damage to electronic components due to electrostatic discharge | ||
Topical note | Notes on avoiding damage through contamination and foreign objects | ||
Notes about Common-Rail components | |||
| Remove | ||
1 | Switch off ignition and store transmitter key outside of transmission range (min. 2 m). | ||
2 | Remove heat shield (4) from exhaust gas turbocharger (8). | ||
3 | Unclip electrical wiring harness from retaining clip (5). | ||
4 | Remove screws (6) and remove right rear engine lifting lug (7). | ||
5 | Disconnect electrical connector (9) from pressure sensor (10). | ||
6 | Remove pressure sensor (10) from right rail (11). | Catch escaping fuel with clean, lint-free dry cloths. | |
| Install | ||
7 | Screw pressure sensor (10) into right rail (11). | ||
Note on calculation of tightening torque when using insertion or socket tools with various effective lengths | |||
Rail pressure sensor at rail | |||
8 | Connect electrical connector (9). | ||
9 | Insert right rear engine lifting lug (7) and screw in screws (6). | Screw/bolt, engine suspension lug to cylinder head | |
10 | Clip electrical wiring harness into retaining clip (5). | ||
11 | Install heat shield (5) on exhaust gas turbocharger (8). | ||
Only install upper engine cover after the leak test. | |||
12 | Read out and delete fault memory and perform initialization of pressure sensor (10). | If the pressure sensor (10) is replaced. | |
| |||
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
13 | Perform engine test run and check pressure sensor (10) in terms of leak tightness. | ||
14 | Install upper engine cover. |
Powiązane dokumenty
- ad0000s200006p
- ah0000p001501cw Wskazówka dotycząca obliczania momentu dokręcania przy stosowaniu narzędzi o różnej długości dźwigni
- ah0000p500001a Wskazówki dotyczące zapobiegania uszkodzeniom na skutek zabrudzeń i ciał obcych
- ah0716p000201tx Wskazówki dotyczące zespołów układu Common-Rail
- ah5400p000101a Wskazówki dotyczące zapobiegania uszkodzeniom elementów elektronicznych na skutek rozładowania potencjału elektrostatycznego
- ar0940s6045ps
- as0000z000501a Niebezpieczeństwo wypadku na skutek samoczynnego ruszenia przy pracującym silniku. Niebezpieczeństwo obrażeń na skutek zmiażdżenia lub poparzenia przy wykonywaniu czynności podczas rozruchu lub przy pracującym silniku.
- as0716z000101a Niebezpieczeństwo eksplozji w wyniku zapalenia się oparów paliwa. Niebezpieczeństwo obrażeń skóry i oczu przez wytryskujący strumień paliwa.
- as4700z000101a Niebezpieczeństwo wybuchu wskutek zapalenia, niebezpieczeństwo zatrucia wskutek wdychania i połknięcia paliwa oraz niebezpieczeństwo obrażeń wskutek kontaktu skóry i oczu z paliwem.