P15.10-2162-08
1 | Cable tie | T1/1 | Cylinder 1 ignition coil | T1/5 | Cylinder 5 ignition coil | ||
2 | Electrical connector | T1/2 | Cylinder 2 ignition coil | T1/6 | Cylinder 6 ignition coil | ||
3 | Screw | T1/3 | Cylinder 3 ignition coil | T1/7 | Cylinder 7 ignition coil | ||
4 | Spark plug connector | T1/4 | Cylinder 4 ignition coil | T1/8 | Cylinder 8 ignition coil |
| Remove/install | ||
Warning | Risk of injury. Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | |
Danger | Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC) | Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines. | |
Topical note | Information on preventing damage to electronic components due to electrostatic discharge | ||
Topical note | Notes on avoiding damage to ignition system | ||
Warning | Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | No parts of the body or limbs should be within the operating area when the components are moving. | |
1 | Open engine hood and raise to vertical position | ||
2 | Remove air filter housing | ||
3 | Detach electrical feed lines from cylinder 1 ignition coil to cylinder 8 ignition coil (T1/1 to T1/8) at ignition coil | Installation: Replace cable ties (1). | |
4 | Unlock electrical connections (2) for cylinder 1 ignition coil to cylinder 8 ignition coil (T1/1 to T1/8) and detach | ||
5 | Remove bolt (3) | Screw/bolt, ignition coil to cylinder head cover | |
6 | Remove ignition coils for cylinders 1 to 8 (T1/1 to T1/8) and pry off spark plug connectors (4) in this connection via cylinder head covers from spark plugs | Installation: Observe the assignment marks "a" and "b" applied on ignition coils for cylinders 1 to 8 (T1/1 to T1/8) and on the cylinder head covers during attachment of spark plug connectors. | |
Double open-ended wrench | |||
7 | Install in the reverse order | ||
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
8 | Carry out an engine test run |
110 589 01 01 00
Double open-ended wrench
Viitatut asiakirjat
- ah1510p000201d Ohjeita sytytysjärjestelmän vaurioiden välttämiseksi
- ah5400p000101a Ohjeita elektronisten rakenneosien sähköstaattisen varauksen purkautumisen aiheuttamien vaurioiden välttämiseksi
- ar0910p1150rt
- ar0910p1150rtb
- ar0910p1150rtc
- ar8840p1000rt Konepellin avaaminen, nostaminen pystyyn ja sulkeminen
- as0000z000201a Loukkaantumisvaara: Kuumat tai hehkuvat esineet voivat aiheuttaa palovammoja.
- as0000z000501a Onnettomuusvaara: Varo moottorin käydessä, ettei auto lähde liikkeelle. Loukkaantumisvaara: Varo liikkuvia ja kuumia osia moottorin käydessä ja moottoria käynnistettäessä
- as0000z001101a Loukkaantumisvaara: Varo, etteivät kätesi jää puristuksiin konepellin, takaluukun, ovien, kansien ja kattoluukun irrotuksessa, asennuksessa ja säätötöissä.
- as0000z003501a Hengenvaara suoritettaessa töitä rakenneosille ja järjestelmille, joissa on U >= 30 V vaihtojännite (AC) tai U >= 60 V tasajännite (DC)