ESP braking moment control circuit, function

CAN B

CAN C

ESP control module
(N47-5)

ESP hydraulic unit
(A7/3)

Solenoid valves

(A7/3y5 to A7/3y15)

High-pressure/return

pump (A7/3m1)

Injection and ignition system (ME-SFI) control module

ETC [EGS] control module (N15/3)

Voltage, terminals 30, 31, 87

Left front rpm sensor (L6/1)

Right front rpm sensor (L6/2)

Left rear rpm sensor (L6/3)

Right rear rpm sensor (L6/4)

Parking brake indicator switch (S12)

High pressure/
return pump relay (K40/6kF )

Diagnostic data link connector (X11/4)

Stop lamp switch (S9/1)

ESP OFF switch (S76/6)

Instrument cluster (A1)

ESP warning lamp (A1e41)

ABS malfunction indicator lamp (A1e17)

Multifunction display (A1p13)

Upper control panel control module (N72/1)

Control module

Left SAM (N10/6)

DI control module (N73)

Jacket tube module

(N80)

Steering angle sensor

(N49)

Engines 112, 113:

Rotational speed sensor (N64)

ESP brake pressure sensor (B34)

Engines 112, 113:

Lateral acceleration sensor (B24/2)

BAS brake booster (A7/7)

BAS solenoid valve (A7/7y1)

BAS release switch (A7/7s1)

BAS diaphragm travel sensor (A7/7b1)

Control module

Rear SAM (N10/8)

On engines 137, 613:

Yaw rate and lateral acceleration sensor (B24/15)

The functions of the braking moment control circuit are controlled using the components of the electric/electronic system.

The voltage for circuit 30 of the ESP control module (N47-5) is supplied by the left fuse and relay module (K40/6); the voltage for circuit 87 is supplied via the right fuse and relay box (F1/1).

The ESP control module (N47-5) receives input signals from the following components:

 4 wheel speed sensors

 Steering angle sensor over CAN data line

 Lateral acceleration sensor

 Yaw rate sensor

 ESP brake pressure sensor

 Stop lamp switch

 Parking brake switch over CAN data line

 ME-SFI control module over CAN data line

 ETC control module over CAN data line

 ESP OFF switch over CAN data line

 BAS release switch

 BAS diaphragm travel sensor

-----------------------------------------------------------------------------------------

The input signals are processed in the ESP control module to form output signals for the following components:

 BAS solenoid valve

 Solenoid valves in the hydraulic unit

 High-pressure/return pump (via relays)

 ME-SFI control module over CAN data line

 ETC control module over CAN data line

 ESP warning lamp over CAN data line

 ABS indicator lamp over CAN data line

 Multifunction display over CAN data line

 Brake lamps via rear SAM

The ESP control module (N47-5) uses the input signals to decide which of the 8 modes

 Normal mode

 ABS control mode

 ASR control mode

 EBR control mode (see drive moment control circuit)

 ESP control mode

 ESP OFF mode

 BAS mode

 DTR control mode

must be activated.

-----------------------------------------------------------------------------------------

Normal mode

This is the case when the driving state requires no control mode. All solenoid valves in the ESP hydraulic unit (A7/3) are in the basic position, i.e. switched to the de-energized position. The system is ready for braking.

This mode also exists when there is a malfunction in the ESP, BAS or ABS system. Drive torque control is not activated.

ABS control mode

The ESP control module (N47-5) uses the wheel speed signals to detect that ABS control is required and the appropriate solenoid valves are actuated in the hydraulic unit.

The solenoid valves for the front and rear axle in the ESP hydraulic unit (A7/3) are actuated individually (4-channel control).

ASR control mode

As soon as a wheel begins to spin, the ESP control module (N47-5) actuates the high pressure and return pump (A7/3m1), the rear axle switchover solenoid valve, the rear axle inlet solenoid valve and the solenoid valves for the rear axle. The solenoid valves for the rear axle are actuated independently for the left and right sides.

-----------------------------------------------------------------------------------------

ESP control mode

The ESP control module (N47-5) receives and processes the signals for the wheel speeds, the steer angle, the yaw rate of the vehicle, the lateral acceleration and the brake pressure in the front axle circuit. After evaluating the input signals, the BAS solenoid valve (A7/7y1), inlet solenoid valves, switchover valves, high pressure and return pump (A7/3m1), and the required solenoid valves are actuated in order to regulate the brake pressure in the individual wheel brakes.

ESP OFF mode

If the driver presses the ESP OFF switch (S76/6) the ESP acceleration slip regulation is deactivated and the ESP stability function is also switched off when the vehicle accelerates and when rolling. The ESP stability function remains operational during braking. EBR control is deactivated.

In this switch position one brake is applied via the braking moment control circuit up to a speed of 40 km/h if onewheel begins to spin. If activation conditions continue to exist, brake intervention continues up to max. 60 km/h. The braking torque is, however, reduced continuously.

BAS mode

The ESP control module (N47-5), uses the speed at which the driver presses the brake pedal to detect that emergency braking is required and initiates the BAS mode (refer to BAS Function).

-----------------------------------------------------------------------------------------

Distronic control mode

The Distronic control module (DTR) transmits the signals for ART control to the ESP control module. There the requests are prioritized and forwarded to the engine control module, and if necessary a braking action is carried out by actuating the BAS solenoid valve.

The transmission display and warning function of the DTR is transmitted direct to the relevant receivers.