Remove, install soundproofing

AR60.00-S-1752S

Remove, install soundproofing

03.12.2019

Model

636, 639

Shown on model 639.605 without code T19 (Left sliding door)

1

Damping with foam flakes in bag 190190 mm

2

Damping with foam flakes in bag 200200 mm

3

Damping with foam flakes in bag 250350 mm

5

Damping with foam flakes in bag 245610 mm

A

Area of center left A-pillar, 3 insulation bag size 3

B

Area of lower left A-pillar, 2 insulation bag size 3

C

Area of lower left B-pillar, 1 insulation bag size 3 and 1 insulation bag size 2

D

Area of left front lower side wall paneling, 2 insulation bag size 5

E

Area of left lower C-pillar, 1 insulation bag size 3

F

Area of center left C-pillar, 1 insulation bag size 3 (without code T19 (Left sliding door))

G

Area of left lower rear center section, 2 insulation bag size 3

H

Area of left front upper roof frame, 3 insulation bag size 1

I

Area of left upper C-pillar, 1 insulation bag size 3 (without code T19 (Left sliding door)) or 2 insulation bag size 1 (with code T19 (Left sliding door))

J

Area of left upper rear sidewall paneling, 1 3Binsulation bag size 3. Area of left upper rear sidewall paneling, 1 insulation bag size 3

K

Area of left upper D-pillar, 2 insulation bag size 3

L

Area of upper rear roof frame, 2 insulation bag size 1

Shown on model 639.605 without code T19 (left sliding door)

1

Damping with foam flakes in bag 190190 mm

3

Damping with foam flakes in bag 250350 mm

4

Damping with foam flakes in bag 185185 mm

M

Area of center right A-pillar, 3 insulation bag size 3

N

Area of lower right A-pillar, 2 insulation bag size 3

O

Area of lower right B-pillar, 2 insulation bag size 3 and 1 insulation bag size 4

P

Area of right lower C-pillar, 1 insulation bag size 3

Q

Area of right lower rear center section, 2 insulation bag size 3

R

Area of right front upper roof frame, 3 insulation bag size 1

S

Area of right upper C-pillar, 2 insulation bag size 1

T

Area of upper rear right sidewall paneling, 1 insulation bag size 3

U

Area of right upper D-pillar, 2 insulation bag size 3



Remove

 Danger

Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC)

Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines.

AS00.00-Z-0035-01A

Topical note

General information on handling vehicles with high-voltage on-board electrical system and/or lithium-ion battery and/or gaseous-fuel drive system

AH00.00-Z-0300-01A

1

Remove damping (1, 2, 3, 4, 5) from the respective repair area

 The corresponding repair area must be accessible, if necessary remove detachable parts in repair area.



Install

2

Install damping (1, 2, 3, 4, 5)


Always replace damaged damping (1, 2, 3, 4, 5).
This prevents noise development when the vehicle is being operated.

 To install, punch small bleed hole into corresponding damping (1, 2, 3, 4, 5), press damping (1, 2, 3, 4, 5) together and install in corresponding repair area. If applicable, reinstall detachable parts.