ar4245w2003a

Manually change parameters for ESP(R) closed-loop control after vehicle modification

Type ar · emne 42.45 · version 0502 · 2018-09-05

Gælder for: Model 963, 964 with code S1D (Stability Control Assist (ESP))

Ikke tilgængelig på “da”; vises på Engelsk.

Placering

Funktionsgruppe 2 Chassis › 42 Bremsehydraulik og -mekanik › 42.45 Elektronisk stabilitetsprogram (ESP), stabilitetsregulering (SR) — Serie 963 · Serie 964

EinPAS 26 Aktive sikkerhedssystemer › 26.20 Bremse-/traktionsregulering › 26.20.1 Grundinformation — Serie 963 · Serie 964

AR42.45-W-2003A

Manually change parameters for ESP(R) closed-loop control after vehicle modification

28.08.2018

Model

963, 964

with code S1D (Stability Control Assist (ESP))

General information on change to parameters for ESP(R) closed-loop control after vehicle modification

AH42.45-N-0002-01A

Update Vehicle Documentation (VeDoc)

1

Print out and fill out form for liability disclaimer.

OF00.00-W-3000-10A

2

Document conversion scope, relevant service codes and, where applicable, the number of the certificate of non-objection (CNO) in VeDoc.

The scope of modification to be documented can be found in the liability disclaimer.

Parameterization

3

Connect diagnostic system and start XENTRY.

4

Perform initial quick test.

The initial quick test is saved until the end of the diagnosis session as an initial quick test.

5

Delete fault memory in all the control units.

6

Change parameter "Wheelbase".

Only if the wheelbase had been changed.

To do so, select following menu items:
Special functions 
Change parameters for ESP® control with special ESP® authorization after vehicle conversion 
Manually change parameters for ESP® control after vehicle modification 
A2 (Central gateway (CGW) control unit) 
Wheelbase

7

Change parameter "Car transporter".

Only if the vehicle had been modified for operation as car transporter.

To do so, select following menu items:
Special functions 
Change parameters for ESP® control with special ESP® authorization after vehicle conversion 
Manually change parameters for ESP® control after vehicle modification 
A2 (Central gateway (CGW) control unit) 
Car transporter (semitrailer tractor)

8

Change parameter "Car transporter anti-swerve brake".

Only if the vehicle had been modified for operation as car transporter and an anti-swerve brake was installed.

To do so, select following menu items:
Special functions 
Change parameters for ESP® control with special ESP® authorization after vehicle conversion 
Manually change parameters for ESP® control after vehicle modification 
A10b (Electronic brake system (EBS) control unit) 
Car transporter anti-swerve brake

9

Change parameter "Vehicle type".

Only if the vehicle type was changed (e.g. when a dumper vehicle is converted to a platform truck).

To do so, select following menu items:
Special functions 
Change parameters for ESP® control with special ESP® authorization after vehicle conversion 
Manually change parameters for ESP® control after vehicle modification 
A2 (Central gateway (CGW) control unit) 
Vehicle model

10

Change parameter "Transmission model".

Only if the transmission model was changed.

To do so, select following menu items:
Special functions 
Change parameters for ESP® control with special ESP® authorization after vehicle conversion 
Manually change parameters for ESP® control after vehicle modification 
A2 (Central gateway (CGW) control unit) 
Transmission model

11

Change parameter "Retarder".

Only if the retarder model was changed.

To do so, select following menu items:
Special functions 
Change parameters for ESP® control with special ESP® authorization after vehicle conversion 
Manually change parameters for ESP® control after vehicle modification 
A2 (Central gateway (CGW) control unit) 
Retarder

12

Change parameter "Suspension type for axles 1 to 4".

Only if the suspension type on axles 1 to 4 was changed.

To do so, select following menu items:
Special functions 
Change parameters for ESP® control with special ESP® authorization after vehicle conversion 
Manually change parameters for ESP® control after vehicle modification 
A2 (Central gateway (CGW) control unit) 
Axle 1 to 4 suspension type

13

Change parameter "Center of gravity height".

Only if the center of gravity height was changed.

To do so, select following menu items:
Special functions 
Change parameters for ESP® control with special ESP® authorization after vehicle conversion 
Manually change parameters for ESP® control after vehicle modification 
A10b (Electronic brake system (EBS) control unit) 
or
A10c (Electronic brake system (EBS) control unit) 
Height of vehicle's center of gravity

14

Change parameter "Trailer operation with semitrailer tractor".

Model 963, 964 except code S1E (ESP for trailer operation with semitrailer tractors)
Only if a trailer hitch had been mounted in addition to the existing fifth wheel coupling.

To do so, select following menu items:
Special functions 
Change parameters for ESP® control with special ESP® authorization after vehicle conversion 
Manually change parameters for ESP® control after vehicle modification 
A10b (Electronic brake system (EBS) control unit) 
or
A10c (Electronic brake system (EBS) control unit) 
Trailer operation with semitrailer tractor

15

Change parameter "Auxiliary stabilizer".

Only when an auxiliary stabilizer was fitted to the rear axle or the trailing axle.

To do so, select following menu items:
Special functions 
Change parameters for ESP® control with special ESP® authorization after vehicle conversion 
Manually change parameters for ESP® control after vehicle modification 
A10c (Electronic brake system (EBS) control unit) 
Auxiliary stabilizer

16

Change parameter "Distance between axles 2 and 3".

Only if the distance between axles 2 and 3 was changed.

To do so, select following menu items:
Special functions 
Change parameters for ESP® control with special ESP® authorization after vehicle conversion 
Manually change parameters for ESP® control after vehicle modification 
A10b (Electronic brake system (EBS) control unit) 
Distance between axles 2 and 3

17

Change parameter "Distance between axles 3 and 4".

Only if distance between axles 3 and 4 was changed.

To do so, select following menu items:
Special functions 
Change parameters for ESP® control with special ESP® authorization after vehicle conversion 
Manually change parameters for ESP® control after vehicle modification 
A10b (Electronic brake system (EBS) control unit) 
Distance between axles 3 and 4

18

Complete parameterization procedure.

To do so, select following menu items:
Special functions 
Change parameters for ESP® control with special ESP® authorization after vehicle conversion 
Manually change parameters for ESP® control after vehicle modification 
Complete process.

After the required teach-in run, print out event log of teach-in process.

19

Perform final quick test; print out initial quick test and final quick test.

There must be no fault codes in the control units being updated.

If fault codes are still present in control units being updated,

then process the fault codes.

After obtaining special order.

20

End XENTRY and remove the diagnostic system.

21

Store available documents and printouts in a tamperproof manner.

Henviste dokumenter