W13.30-1209-09
Shown on engine with compressor (5) from Voith |
1 | Resonator | 5 | Compressor | 9 | Power steering pump | ||
2 | Pipes | 6 | Bracket | A4 | Engine management control unit (MCM) | ||
3 | Engine oil filler pipe | 7 | Oil suction hose | ||||
4 | Compressed-air line | 8 | Oil pressure line |
W13.30-1210-07
Shown on engine with compressor (5) from Voith |
5 | Compressor | 10 | Coolant lines | 11 | Bracket |
Shown on compressor (5) from Voith |
5 | Compressor |
12 | Drive gear |
13 | Sealing ring |
14 | Sealing ring |
15 | Fitting |
16 | Fitting |
W13.30-1211-06
Danger ! | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
Danger ! | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure with the safety strut. | |
Danger ! | Risk of injury to skin and eyes suffering scalding from contact with hot coolantspray. Risk of poisoning from swallowing coolant. | Do not open cooling system unless coolant temperature is below 90 °C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers. | |
| Notes on avoiding damage through contamination and foreign objects | ||
| Notes on self-locking nuts and bolts | ||
| Notes on coolant | ||
| Notes on tilting the cab | ||
| Notes on engine oil | ||
| Remove/install | ||
1 | Tilt cab | Installation: Only tilt back cab after the leak test. | |
2 | Remove soundproofing | ||
3 | Drain coolant at engine radiator | ||
4 | Remove resonator (1) | ||
5 | Remove suction lines (2) for hydrostatic fan drive on frame | ||
6 | Remove engine oil filler pipe (3) on the oil pan | ||
7 | Expose engine oil filler pipe (3) and bind to one side | ||
8 | Remove engine management (MCM) control unit (A4) | ||
9 | Remove compressed air line (4) from compressor (5) | Installation: Check compressed-air line (4) for carbonization. In event of any carbonization the air line (4) and the carbonized parts must be replaced. | |
Union nut, air line to fitting for compressor | |||
10 | Remove control line from compressor (5) | Only for compressor (5) from Knorr. | |
Installation: Replace sealing ring. | |||
Union nut, control line to compressor | |||
11 | Remove bracket (6) for the fuel lines | ||
12 | Remove oil suction hose (7) and oil pressure line (8) for power steering pump (9) on vehicle frame | ||
13 | Remove power steering pump (9) from compressor (5) and place with attached oil suction hose (7) and oil pressure line (8) to one side | Bolt, power steering pump to compressor | |
14 | Release and remove coolant lines (10) on compressor (5) | Collect flowing out coolant in a suitable container. | |
15 | Remove bracket (11) | Bolt, bracket for compressor to crankcase | |
Bolt, bracket to compressor | |||
16 | Remove compressor (5) from timing case | Collect escaping engine oil in a suitable container. | |
Installation: First insert the rear upper screw/bolt, then place compressor (5) on the timing case. Turn the drive gear (12) of the compressor (5). | |||
Bolt, compressor to timing case | |||
17 | Remove drive gear (12) | Only if the drive gear (12) is damaged. | |
Installation: Attach new drive gear (12) and also check the counter-gearwheel for the gearwheel drive involved for damage; replace if necessary; replace if necessary. | |||
Nut, (left-hand thread) drive gear to compressor | |||
18 | Remove sealing rings (13, 14) at compressor (5) | Installation: Renew sealing rings (13, 14). | |
19 | Remove fitting (15) on compressor (5) | Only if compressor (5) was replaced or fitting (15) is leaky. | |
Fitting to compressor | |||
20 | Remove fitting (16) for coolant lines (10) on compressor (5) | Only if compressor (5) was replaced or fitting (16) is leaky. | |
Fitting, coolant line to compressor | |||
21 | Install in the reverse order | ||
22 | Check engine oil level at display; correct if necessary | Observe set engine oil specification in the maintenance system. | |
23 | Start engine and perform an engine test run | Allow engine to run at a higher rotational speed. | |
24 | Check all connectors on the compressor (5) for leaktightness and stop engine | Visual inspection. |
Henviste dokumenter
- ah0000n000101a Oplysninger om selvlåsende bolte og møtrikker
- ah0000n500001h Oplysninger om forebyggelse af skader på grund af snavs og fremmedlegemer
- ah1800n010101ha Oplysninger om motorolie
- ah2000n208001a Oplysninger om kølervæske
- ah6080n000301a Oplysninger om tipning af førerhus
- ar0708w7013ne
- ar1310w5840ne
- ar2000w1142ne
- as0000z000501a Fare for ulykke ved automatisk igangsætning når motoren kører. Fare for personskade på grund af knusning og forbrænding, hvis der arbejdes mens motoren startes eller kører
- as2000z000101a Risiko for skoldningsskader på hud og øjne pga. sprøjtende, varm kølervæske. Risiko for forgiftning ved indtagelse af kølervæske
- as6080z000101a Fare for personskade ved fastklemning og knusning, når førerhuset tippes