W07.08-1018-09
1 | Electrical connector | 5 | Electrical wiring harness | 8 | Electrical connector | ||
2 | Rubber damper | 6 | Screw | 9 | Bracket | ||
3 | Bolts | 7 | Guide tube (oil dipstick) | A4 | Engine management control unit (MCM) | ||
4 | Electrical connector |
Warning | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure it with the safety strut. | |
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
Topical note | Information on preventing damage to electronic components due to electrostatic discharge | ||
Topical note | Notes on tilting the cab | ||
Notes on safety-relevant components | |||
| Remove | ||
1 | Connect diagnostic system, start XENTRY and perform quick test. | Only if motor control module will be replaced. | |
2.1 | Select "Control unit replacement" and follow the instructions. | If the motor control module will be replaced. | |
Control unit replacement is completely menu-assisted under: | |||
2.2 | Switch off ignition. | If the motor control module will not be replaced. | |
3 | Tilt cab. | ||
4 | Remove soundproofing. | ||
5 | Disconnect electrical connector (1) and remove plug at bracket. | ||
6 | Disconnect electrical connector (4) at motor control module. | ||
7 | Remove screw (6) and disconnect electrical connector (8) at motor control module. | ||
8 | Expose electrical wiring harness (5) at motor control module. | ||
9 | Unclip guide tube (7) at bracket (9). | ||
10 | Remove screws (3). | ||
11 | Detach motor control module with rubber dampers (2) and remove. | ||
12 | Remove bracket (9) at motor control module. | Only if motor control module will be replaced. | |
| Install | ||
13 | Install bracket (9) at motor control module. | Only if motor control module will be replaced. | |
Bolt, holder for oil suction tube/wiring harness to engine management (MCM) control unit | |||
14 | Install motor control module with rubber dampers (2). | ||
15 | Tighten screws (3). | Screw/bolt, engine management (MCM) control unit to fuel filter module | |
16 | Clip in guide tube (7) at bracket (9). | ||
17 | Attach electrical wiring harness (5) at motor control module. | ||
18 | Connect electrical connector (8) to motor control module and tighten screw (6). | Bolt, electrical connection to engine management (MCM) control unit | |
19 | Connect electrical connector (4) to motor control module. | ||
20 | Connect electrical connector (1) and attach plug to bracket. | ||
21 | Install soundproofing. | ||
22 | Tilt back cab. | ||
23 | Follow instructions for "Control unit replacement" in XENTRY. | Only if motor control module was replaced. | |
| Check | ||
24 | Perform engine test run. | Only if motor control module was replaced. | |
25 | Check the engine management for proper operation. | Only if motor control module was replaced. | |
26 | End XENTRY and remove the vehicle diagnosis system. | Only if motor control module was replaced. |
Henviste dokumenter
- ah0000z001901a Oplysninger om sikkerhedsrelevante komponenter
- ah5400p000101a Oplysninger med henblik på at undgå skader på elektroniske komponenter på grund af elektrostatisk afladning
- ah6080n000301a Oplysninger om tipning af førerhus
- ar0708w100001a
- as0000z000501a Fare for ulykke ved automatisk igangsætning når motoren kører. Fare for personskade på grund af knusning og forbrænding, hvis der arbejdes mens motoren startes eller kører
- as6080z000101a Fare for personskade ved fastklemning og knusning, når førerhuset tippes