P00.20-2877-08
Shown on model 166.003 |
30 | Front underfloor paneling | 32 | Rear underfloor paneling | |
31 | Center underfloor paneling |
Shown on model 292 with code 489 (AIRMATIC) without code 468 (ACTIVE CURVE SYSTEM) |
1 | Front axle carrier |
2 | Front axle carrier elastomer bearings |
3 | Stabilizer bushings |
5 | Shock absorber elastomer bearing |
6 | Lower supporting ball joint boot |
7 | Lower supporting ball joint |
24 | Elastomer bearing on lower wishbone control arm |
P33.10-2465-06
Shown on model 292 with code 489 (AIRMATIC) |
10 | Clip |
11 | Outer axle shaft boot |
26 | Inner axle shaft boot |
28 | Drive shaft |
P33.10-A008-06
Shown on model 292 with code 489 (AIRMATIC) |
4 | Lower wishbone control arm |
6 | Lower supporting ball joint boot |
7 | Lower supporting ball joint |
10 | Clip |
11 | Outer axle shaft boot |
13 | Lower shift rail elastomer bearing |
14 | Shift rail |
15 | Upper shift rail joint boots |
P33.10-A009-06
Shown on model 292 with code 489 (AIRMATIC) |
19 | Upper supporting ball joint boot |
20 | Upper wishbone control arm |
22 | Upper elastomer bearing |
23 | Level sensor linkage |
P33.10-2469-06
Warning | Risk of injury. Moving parts can pinch, crush or, in extreme cases even sever extremities. | No parts of the body or limbs should be within the operating area of mechanical components when moving components. | |
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
Danger | Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC) | Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines. | |
Topical note | General information on handling vehicles with high-voltage on-board electrical system and/or lithium-ion battery and/or gaseous-fuel drive system | ||
Preparatory activity | |||
1 | Lift vehicle with lifting platform. | ||
| |||
| Check | ||
2 | Check underfloor paneling for evidence of damage caused by driving over obstacles or bottoming. | If the underfloor paneling exhibits any signs of damage, | |
| |||
rectify the problems. | |||
After obtaining special order. | |||
| Remove | ||
3.1 | Remove front underfloor paneling (30), center underfloor paneling (31) and rear underfloor paneling (32). | Model 166, 292 | |
| |||
3.2 | Install front engine compartment lining, center engine compartment lining, rear engine compartment lining. | Model 167 | |
| |||
| Check | ||
4 | Assess the wheel bearings by firmly tugging, pushing and turning at the wheels. | If problems occur, | |
| |||
rectify the problems. | |||
After obtaining special order. | |||
5 | Check front axle carrier (1) for cracks, deformation and corrosion. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
6 | Check front axle carrier elastomer bearings (2) for cracks, deformation and wear, also check for play by firmly pulling and pushing. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
7 | Check stabilizer bar for cracks, deformation and corrosion. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
8 | Check stabilizer bar bushings (3) for cracks, deformation and wear, also check for play by firmly pulling and pushing on stabilizer bar. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
9 | Check shock absorber elastomer bearings (5) for cracks, deformation and wear, also check for play by firmly pulling and pushing. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
10 | Check lower wishbone control arm elastomer bearings (24) for cracks, deformation and wear, also check for play by firmly pulling and pushing. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
11 | Check outer drive shaft boots (11) for condition, leak tightness and correct seating. | Model 166 (except 166.006/058), 167 (except 167.148), 292 | |
If necessary, use commercially available devices/tools. | |||
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
12 | Check clamps (10) of outer drive shaft boots (11) for cracks, deformation, corrosion and correct seating. | Model 166 (except 166.006/058), 167 (except 167.148), 292 | |
If necessary, use commercially available devices/tools. | |||
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
13 | Check inner drive shaft boots (26) for condition, leak tightness and correct seating. | Model 166 (except 166.006/058), 167 (except 167.148), 292 | |
If necessary, use commercially available devices/tools. | |||
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
14 | Check clamps (10) of inner drive shaft boots (26) for cracks, deformation, corrosion and correct seating. | Model 166 (except 166.006/058), 167 (except 167.148), 292 | |
If necessary, use commercially available devices/tools. | |||
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
15 | Check drive shafts (28) for cracks, deformation, corrosion and play by pulling and pushing. | Model 166 (except 166.006/058), 167 (except 167.148), 292 | |
If necessary, use commercially available devices/tools. | |||
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
16 | Check lower supporting joint boots (6) for condition, leak tightness and correct seating. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
17 | Check lower supporting joints (7) for play by firmly pushing and pulling lower wishbone control arms (4). | If problems occur, | |
| |||
rectify the problems. | |||
After obtaining special order. | |||
18 | Check upper shift rail joint boots (15) for condition, leak tightness and correct seating. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
19 | Check shift rail joints for play by firmly pulling and pushing on shift rails (14). | If problems occur, | |
| |||
rectify the problems. | |||
After obtaining special order. | |||
20 | Check lower shift rail elastomer bearings (13) for play by firmly pulling and pressing on shift rails (14). | If problems occur, | |
| |||
rectify the problems. | |||
After obtaining special order. | |||
21 | Check shift rails (14) for cracks, deformation and corrosion. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
22 | Check upper elastomer bearings (22) of upper wishbone control arms (20) for cracks, deformation and wear, also check for play by firmly pulling and pushing. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
23 | Check upper supporting joint boots (19) for condition, leak tightness and correct seating. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
24 | Check upper supporting joints for play by firmly pulling and pushing upper wishbone control arms (20). | If problems occur, | |
| |||
rectify the problems. | |||
After obtaining special order. | |||
25 | Check level sensor linkage (23) for correct seating, cracks, deformation, corrosion and play. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
| Install | ||
26.1 | Install front underfloor paneling (30), center underfloor paneling (31) and rear underfloor paneling (32). | Model 166, 292 | |
| |||
26.2 | Install front engine compartment lining, center engine compartment lining, rear engine compartment lining. | Model 167 | |
|