ar4215w0010b
Remove/install automatic linkage adjuster
Typ ar · téma 42.15 · verzia 0121 · 2015-09-22
Platí pre: Model 374, 375.3, 940, 942, 943, 944, 949, 950, 952, 953, 954, 958.2/4 Rear axle with drum brake Model 930, 932, 933, 934 Rear axle with drum brake with brake wear sensor
Nie je k dispozícii v jazyku „sk“; zobrazené v jazyku Anglicky.
Zaradenie
Funkčná skupina 2 Podvozok › 42 Hydraulika a mechanika bŕzd › 42.15 Mechanika — Rad 374 · Rad 375 (modely 3**) · Rad 930 · Rad 932 · Rad 933 · Rad 934 · Rad 940 · Rad 942 · Rad 943 · Rad 944 · Rad 949 · Rad 950 · Rad 952 · Rad 953 · Rad 954 · Rad 958 (modely 2**, 4**)
EinPAS 21 Brakes/vacuum system/compressed-air system › 21.15 Service brake/vacuum system › 21.15.40 Service brake, front — Rad 374 · Rad 375 (modely 3**) · Rad 930 · Rad 932 · Rad 933 · Rad 934 · Rad 940 · Rad 942 · Rad 943 · Rad 944 · Rad 949 · Rad 950 · Rad 952 · Rad 953 · Rad 954 · Rad 958 (modely 2**, 4**)
EinPAS 21 Brakes/vacuum system/compressed-air system › 21.15 Service brake/vacuum system › 21.15.42 Service brake, rear — Rad 374 · Rad 375 (modely 3**) · Rad 930 · Rad 932 · Rad 933 · Rad 934 · Rad 940 · Rad 942 · Rad 943 · Rad 944 · Rad 949 · Rad 950 · Rad 952 · Rad 953 · Rad 954 · Rad 958 (modely 2**, 4**)
AR42.15-W-0010B
| Remove/install automatic linkage adjuster
| 17.09.2015
|
Model
| 374, 375.3, 940, 942, 943, 944, 949, 950, 952, 953, 954, 958.2/4
|
|
| Rear axle with drum brake
|
Model
| 930, 932, 933, 934
|
|
| Rear axle with drum brake with brake wear sensor
|
Shown on rear axle 748.23
|
1
| Pin
|
| 6
| Thrust plate
|
| 11
| Brake camshaft
|
2
| Washer
|
| 7
| Brake wear sensor
|
| 12
| Adjustment screw
|
3
| Cotter pin
|
| 8
| Screw
|
| 13
| Drifts
|
4
| Screw
|
| 9
| Control arm
|
| 14
| Brake shoes
|
5
| Retaining ring
|
| 10
| Linkage adjuster
|
| Pfeil
| Direction of stop
|
| Remove
|
|
|
1
| Secure vehicle against rolling
|
|
|
2
| Release parking brake
| To release the combination brake cylinder a reservoir pressure of at least 8 bar must be given.
|
|
3
| Remove brake wear sensor (7)
|
| AR42.10-W-1050A
|
4
| Turn brake camshaft (11) and linkage adjuster (10) back to starting position using adjusting screw (12).
| Turn adjusting screw (12) counterclockwise. Creaking noises occur when turning screw.
|
|
5
| Remove brake drum
|
| AR42.10-W-1010A
|
6
| Remove pin (1)
|
|
|
7
| Remove bolt (8) from control arm (9)
|
|
|
8
| Wedge brake shoes (14) using suitable drifts (13) and pull out brake camshaft (11) until linkage adjuster (10) can be removed
|
|
|
9
| Remove linkage adjuster (10) from brake camshaft (11)
|
|
|
| Automatic linkage adjuster modified
|
| BT42.15-W-0001-01A
|
10
| Remove shim from brake camshaft (11)
| The shim is not shown in the graphic. It is located between linkage adjuster (10) and bearing bracket.
|
|
| Install
|
|
|
11
| Slide shim onto brake camshaft (11)
|
|
|
12
| Position linkage adjuster (10) on brake camshaft (11)
|
|
|
| Automatic linkage adjuster modified
|
| BT42.15-W-0001-01A
|
13
| Slide brake camshaft (11) up to contact surface in stop direction (arrow)
|
|
|
14
| Install bolt (1)
| It must be possible to insert pin (1) without resistance.
|
|
15
| Push on washer (2) and secure bolt (1) using new cotter pin (3)
|
|
|
16
| Adjust control arm (9) at linkage adjuster (10)
|
| AR42.15-W-0010-02A
|
|
|
| Bolt, control arm to bearing bracket
| *BA42.15-N-1003-01A
|
17
| Check/adjust axial play of brake camshaft (11)
|
| AR42.15-W-1050-02A
|
|
|
| End play of brake camshaft between brake cam and brake carrier
| *BE42.15-N-1001-01A
|
18
| Install brake drum
|
| AR42.10-W-1010A
|
19
| Install brake wear sensor (7)
|
| AR42.10-W-1050A
|
Test values for mechanical system
|
Number
| Designation
|
| Model 374, 375.3, 958.2/4
| Model 930, 932, 933, 934, 940, 942, 943, 944, 950, 952, 953, 954
|
BE42.15-N-1001-01A
| End play of brake camshaft between brake cam and brake carrier
| mm
| 1,0
| 1,0
|
Test values for mechanical system
|
Number
| Designation
|
| Model 949
|
BE42.15-N-1001-01A
| End play of brake camshaft between brake cam and brake carrier
| mm
| 1,0
|
Brake mechanical system
|
Number
| Designation
|
| Model 374
| Model 375.3, 930, 932, 933, 934, 950, 952, 953, 954
Front axle
|
BA42.15-N-1003-01A
| Bolt, control arm to bearing bracket
| Nm
| 22
| 22
|
Brake mechanical system
|
Number
| Designation
|
| Model 375.3, 930, 932, 933, 934, 950, 952, 953, 954
Rear axle
| Model 940, 942, 943, 944
Front axle
|
BA42.15-N-1003-01A
| Bolt, control arm to bearing bracket
| Nm
| 22
| 22
|
Brake mechanical system
|
Number
| Designation
|
| Model 940, 942, 943, 944
Rear axle
| MODEL 958
|
BA42.15-N-1003-01A
| Bolt, control arm to bearing bracket
| Nm
| 22
| 22
|
Brake mechanical system
|
Number
| Designation
|
| Model 949
Front axle
| Model 949
Rear axle
|
BA42.15-N-1003-01A
| Bolt, control arm to bearing bracket
| Nm
| 22
| 22
|
Odkazované dokumenty
