ar8235p6000q

Remove/install washer fluid reservoir of windshield washer system

Typ ar · temat 82.35 · wersja 0400 · 2007-07-13

Dotyczy: MODEL 209 except CODE (P98) Black Series

Niedostępne w języku „pl”; wyświetlono w języku Angielski.

Umiejscowienie

Grupa funkcyjna 3 Nadwozie › 82 Układ elektryczny, nadwozie › 82.35 Spryskiwacze — Seria 209

EinPAS 36 Widoczność › 36.30 Wycieraczki/ spryskiwacze › 36.30.41 Pompa/ zbiornik/ wymiennik ciepła — Seria 209

AR82.35-P-6000Q

Remove/install washer fluid reservoir of windshield washer system

26.6.07

MODEL 209 except CODE (P98) Black Series

Remove/install washer fluid reservoir of windshield washer system

P82.35-2172-09

Shown on model 209.3 with code 600 Headlamp cleaning system and with code 875 Heated windshield washer system

1 Washing water reservoir

2 Filler neck

3 Electrical connector

4 Electrical connector

5 Electrical connector

M5/2 HCS [SRA] pump (on vehicles with code 600 Headlamp cleaning system)

S42 Windshield washer fluid level indicator switch

6 Bow

7 Bolts

M5/1 Windshield washer fluid pump

Modification notes

2.2.06

Repair method has been revised

Step 3

Remove/install

1

Remove finder liner in front fender

Left, front and center fender liner.

AR88.10-P-1300P

2

Pull filler neck (2) out of washer fluid reservoir (1)

Danger!

Risk of injury to skin and eyes caused by scalding from contact with hot coolant spray. Risk of poisoning caused by swallowing coolant.

Do not open cooling system unless coolant temperature is below 90°C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers.

Wear protective gloves, protective clothing and safety glasses.

AS20.00-Z-0001-01A

3

Use clamps to clamp off both coolant hoses on the heater, release the hose clamps and detach both coolant hoses of the washer fluid heater

For vehicles with code 875 Heated windshield washer system.

*000589543700

4

Unclip bracket (6)

5

Remove windshield washer fluid pump (M5/1) and place to one side with lines attached

Collect washer fluid which flows out.

6

Remove HCS [SRA] pump (M5/2) and place to one side with lines attached

For vehicles with code 600 Headlamp cleaning system.

7

Detach electrical connector (5) from windshield washer fluid level indicator switch (S42)

8

Remove bolts (7)

9

Take off washer fluid reservoir (1)

10

Remove heater unit

Only when replacing the washer fluid reservoir (1) for vehicles with code 875 Heated windshield washer system.

11

Remove windshield washer fluid level indicator switch (S42)

Only when replacing the washer fluid reservoir (1).

12

Install in the reverse order

13

Correct windshield washer system fluid level

Check windshield washer system fluid level and correct if necessary

AP82.35-P-8210P

14

Inspecting cooling system for leaks

For vehicles with code 875 Heated windshield washer system

Engine 112, 113, 271, 612, 646

AR20.00-P-1010P

Engine 156

AR20.00-P-1010TMG

Engine 272, 273

AR20.00-P-1010QB

Engine 642

AR20.00-P-1010PI

Remove/install washer fluid reservoir of windshield washer system

Clamping device

000 589 54 37 00

Powiązane dokumenty