Remove/install power take-off

AR26.45-W-0004CB

Remove/install power take-off

14.06.2019

Transmission

715.310

with power take-off 125

1

Power take-off 1

7

Transmission

S2

Power take-off 1 indicator switch

2

Oil pump housing

8

Pressure relief valve with bypass valve (only on vehicles with code N6Z (Transmission cooling))

Y8

Power take-off 1 solenoid valve

3

Roll pin

9

Pressure relief valve (only on vehicles without code N6Z (Transmission cooling))

Y8a

Power take-off 1 solenoid valve with shift lock

4

Oil pump gear (driven)

10

Electrical connection (PTO indicator switch)

A

Pin

5

Oil pump gear (powered)

11

Electrical connection (PTO solenoid valve)

B

Markings

6

Seal

12

Compressed-air line

Topical note

Notes on self-locking nuts and bolts

AH00.00-N-0001-01A

 

Remove/install

1

Unpressurized circuit 4 of compressed-air system

2

Drain transmission oil from power take-off



Model 963, 964

AP26.00-W-2601H



Model 967

AP26.00-W-2601K

3

Remove output flange from transmission (7)

Transmission 715.310 with code G1E (Transmission G 140-8/9.30-0.79)

AR26.50-W-2000HC

4.1

Remove drive shaft from power take-off 1 (1)

With power take-off (1) with propeller shaft

 Propeller shaft to power take-off

*BA26.45-N-1013-04C

4.2

Remove hydraulic pump

With power take-off (1) with hydraulic pump

AR26.45-W-0002CA

 Do not separate hydraulic lines if possible, collect hydraulic fluid if necessary.

5

Remove power take-off 2

Only for power take-off 125-11b/2c or 125-11c/2c.

AR26.45-W-0009C

 Installation: Replace seal.

6

Disconnect electrical connector (10) from power take-off 1 indicator switch (S2)

 Mark the installation location of the electrical connector (10).

 Installation: Observe the marking for the electrical connector (10).

7

Disconnect electrical connector (11) from power take-off 1 solenoid valve (Y8) or from power take-off 1 solenoid valve with shift lock (Y8a)

 Mark the installation location of the electrical connector (11).

 Installation: Observe marking for electrical connector (11).

8

Detach compressed air line (12) from power take-off 1 solenoid valve (Y8) or from power take-off 1 solenoid valve with shift lock (Y8a)

Model 963, 964

AR42.10-W-0900H

Model 967

AR42.10-W-0900NA

9

Detach air lines and electrical wiring harness with bracket from power take-off 1 (1) and place to one side

 Bolt, power take-off to transmission

*BA26.45-N-1002-04C

10

Unscrew screws/bolts from power take-off 1 (1) and remove power take-off 1 (1)

 Secure power take-off 1 (1) against falling down. The pressure relief valve with bypass valve (8) and the pressure relief valve (9) are under tension.

 Installation: On vehicles with code N6Z (Transmission cooling), the pin (arrow A) of the pressure relief valve with bypass valve (8) must be in "9 o'clock" position.
Replace seal (6).

 Bolt, power take-off to transmission

*BA26.45-N-1002-04C

11

Remove oil pump housing (2), oil pump gear (driven) (4) and oil pump gear (powered) (5)

Only when exchanging transmission or retrofitting a power take-off.

 Installation:
The spring pin (3) for locking the oil pump housing (2) must engage in the blind hole in the transmission housing.
Otherwise; the oil pump housing (2) will be twisted during installation, and the transmission may be damaged.

 Installation: The markings (arrows B) on the oil pump gears (4, 5) must point toward the transmission (7). Lubricate oil pump gears (4, 5).

12

Pour in transmission oil and correct transmission oil level



Model 963, 964

AP26.00-W-2601H



Model 967

AP26.00-W-2601K

13

Install in the reverse order

 Power take-off

Number

Designation

Transmission 715 with PTO 125

BA26.45-N-1002-04C

Bolt, power take-off to transmission

8.8

Nm

50

10.9

Nm

60

 Power take-off

Number

Designation

Transmission 715 with PTO 125

BA26.45-N-1013-04C

Propeller shaft to power take-off

M8

Nm

25

M10

Nm

60

M12

Nm

100