Remove/install oil dipstick guide tube · ar1840p3510rt · Mercedes-Benz WIS

AR18.40-P-3510RT

Remove/install oil dipstick guide tube

24.6.10

ENGINES 113.971 in MODEL 251.075 /175

P18.40-2227-06

1 Oil dipstick guide tube

2 Bolt

3 Shield

4 Bolts

5 Engine cover

6 Sealing ring

 	Remove/install
 Danger!	Risk of injury to skin and eyes caused by handling hot or glowing objects.	Wear safety gloves, protective clothing and safety glasses, if necessary.	AS00.00-Z-0002-01A
 Danger!	Risk of injury caused by fingers being pinched or crushed when removing, installing or aligning hoods, doors, trunk lids, liftgates or sliding roof	Keep body parts and limbs well clear of moving parts.	AS00.00-Z-0011-01A
 Danger!	Risk of death caused by vehicle slipping or toppling off the lifting platform.	Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer.	AS00.00-Z-0010-01A
1	Open engine hood and raise to vertical position		AR88.40-P-1000RT
2	Raise vehicle with vehicle lift		AR00.60-P-1000RT
3	Remove engine cover (5) at front		AR01.10-P-2405RT
4	Pull oil dipstick out of oil dipstick guide tube (1)
5	Remove bolts (4) and take out shield (3)
6	Remove bolt (2)		*BA01.20-P-1001-01E
7	Detach lower engine compartment paneling	 Installation: Install engine compartment paneling only after engine test run.	AR61.20-P-1105RT
8	Remove oil dipstick guide tube (1) up and out	 Installation: Introduce oil dipstick guide tube (1) into oil pan from below.
		 Installation: Replace sealing ring (6) on oil dipstick guide tube (1). When installing oil dipstick guide tube (1), make sure sealing ring (6) is not pressed into the oil pan.
9	Install in the reverse order
	Checking
10	Check engine oil level and correct if required	 The vehicle must be on a level surface otherwise false measurements will occur.	AR18.00-P-3035-01CA
		 Dipstick	*120589072100
 Danger!	Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near the engine as it is running	Secure vehicle to prevent it from moving by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts.	AS00.00-Z-0005-01A
11	Carry out an engine test run and check engine for leaks	 In the event of oil loss determine and eliminate cause, otherwise malfunctions, transmission damage, and serious environmental pollution may occur.

 Crankcase ventilation, cylinder head cover

Number	Designation			Engine 113


BA01.20-P-1001-01E	Cylinder head cover bolt	Stage 1	Nm	9
		Stage 2	°	-

Dipstick

120 589 07 21 00

Referenced documents

ar0060p1000rt Lift/jack up vehicle
ar0110p2405rt Remove/install engine cover
ar0110p2405rtb Remove/install engine cover
ar1800p303501ca Check oil level
ar6120p1105rt Remove/install bottom engine compartment paneling
ar8840p1000rt Opening engine hood, moving to upright position and closing
as0000z000201a Risk of injury. Skin or eye injuries may result when handling hot or glowing objects.
as0000z000501a Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running.
as0000z001001a Risk of death caused by vehicle slipping or toppling off of the lifting platform.
as0000z001101a Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.