Check and adjust front axle toe

AR40.20-D-0323TSF

Check and adjust front axle toe

02.07.2020

Model

910

with code IT3 (3,0 tonner)

except code IT4 (3,5 tonner)

except code IT9 (4.0 tonner)

Model

910

with code IT4 (3,5 tonner)

except code IT3 (3,0 tonner)

except code IT9 (4.0 tonner)

055

Holding device

030

Wheel spreader

Illustration of left side of vehicle

1

Ball head

3

Jam nut

4

Tie rod

Notes on repair work on suspension components

AH00.00-P-0100-01A



Check

1

Check preconditions for wheel alignment.

AR40.20-D-0050TS

 Determine difference between the inner and outer tire tread channel depth here too.

2.1

Determine front-axle level using the angle of the front axle shaft with electronic inclinometer.

When measuring with electronic inclinometer.

AR40.20-D-6870TS

2.2

Determine front-axle level through actual front-axle load.

When measuring without electronic inclinometer.

 Commercially available devices/tools
Wheel load scales

3

Set steering gear to center position.

AR46.20-D-0500-01TS

Topical note

Notes on carrying out repair work in the vehicle interior

AH68.00-N-0001-01S

 Retainer device

*129589012100

 Tensioning nut

*906589002100

If the center position is incorrect,



remove steering wheel, shift by max. one tooth then mount steering wheel again.

Remove/install steering wheel

AR46.10-D-0100TS

4

Install wheel spreader (030), as shown, in direction of travel at front on insides of wheel.

 The elastic bearing of the lower transverse control arm and steering linkage produce a correspondingly large toe value that is reduced to the correct dimension in the ready-to-drive condition.

5

Perform initial measurement.

AR40.20-D-0200TS

 The actual suspension data such as camber, toe, steering axis inclination, caster and the toe-out angle are determined here.

6

Check toe using front-axle level and assign to value in table.

 Observe permissible difference in front axle toe-in between right and left sides of the vehicle.

 If the determined difference between the inner and outer tread groove depth is greater than 2 mm, then values for major wear on the tire outer shoulder must be used.

Total toe

*BE40.20-N-1001-07TSF

Model 910.121/621 except code CB4, CB8, RG8, Z12, model 910.123/623 with code A50, CB7, except code CB4, CB8, RG8, Z12, model 910.123/623 except code A50, CB4, CB8, RG8, Z12, model 910.131/631 except code A50, CB4, CB8, RG8, Z12, model 910.133/633 with code A50, CB7, except code CB4, CB8, ME0, RG8, Z12, model 910.133/633 except code A50, CB4, CB8, ME0, RG8, Z12Toe per wheel

*BE40.20-N-1002-07TSF

Model 910.123/623 with code A50, except code CB4, CB7, CB8, RG8, Z12, model 910.133/633 with code A50, except code CB4, CB7, CB8, ME0, RG8, Z12Toe per wheel

*BE40.20-N-1003-07TSF

Model 910.12/62 with code CB8, except code A50, CB4, CB7, RG8, Z12, model 910.13/63 with code CB8, except code A50, CB4, CB7, ME0, RG8, Z12Toe per wheel

*BE40.20-N-1004-07TSF

Model 910.1/6 with code A50, CB8, except code CB4, CB7, ME0, RG8, Z12Toe per wheel

*BE40.20-N-1005-07TSF

Model 910.0 with code A50, except code RG8, model 910.0 with code RG8, model 910.1 with code CB4, except code CB7, CB8, RG8, Z12Toe per wheel

*BE40.20-N-1006-07TSF

Model 910.1/6 with code IT3, RG8, except code CB4, CB7, CB8, ME0, Z12, model 910.1/6 with code IT4, RG8, except code CB7, ME0, Z12, model 910.1/6 with code Z12, except code A50, CB4, CB7, CB8, ME0Toe per wheel

*BE40.20-N-1007-07TSF

Model 910.633 with code ME0Toe per wheel

*BE40.20-N-1008-07TSF

Adjust

7

Adjust toe to determined specified value.

If the actual values deviate from the specified values or if the tire outer shoulder exhibits wear.

Note on calculation of tightening torque when using insertion or socket tools with various effective lengths

AH00.00-P-0015-01CW

 To do so, release counternuts (3), adjust toe by turning tie rods (4) then tighten counternuts (3) again. Counterhold the ball heads (1) while doing so.

 Counternut, tie rod to ball head

*BA46.40-N-1001-06TS

8

Check bellows of tie rods (4) for twisting.

If corresponding findings are present,



Correct the position of affected boots.

9

Remove holding device (055) and tensioning nut.

 Retainer device

*129589012100

 Tensioning nut

*906589002100

10

Remove wheel spreader (030).



Check

11

Perform final measurement.

AR40.20-D-0200TS

Front axle toe

Number

Designation

Model 910.121/621 with code IT3, except CB4, CB8, RG8, Z12,
model 910.123/623 with code A50, CB7, IT3, except code CB4, CB8, RG8, Z12,
model 910.123/623 with code IT3, except code A50, CB4, CB8, RG8, Z12,
model 910.131/631 with code IT4, except CB4, CB8, RG8, Z12,
model 910.133/633 with code A50, CB7, IT4, except code CB4, CB8, ME0, RG8, Z12,
model 910.133/633 with code IT4, except code A50, CB4, CB8, ME0, RG8, Z12

Model 910.123/623 with code A50 IT3, except code CB4 CB7 CB8, RG8, Z12,
model 910.133/633 with code A50 IT4 CB4, except code CB7 CB8 ME0, RG8, Z12

BE40.20-N-1001-07TSF

Total toe

Permissible difference in front axle toe between right and left sides of vehicle

°

0° 05'

0° 05'

Maximum tolerance

°

0° 10'

0° 10'

Front axle toe

Number

Designation

Model 910.12/62 with code CB8 IT3, except code A50 CB4 CB7, RG8, Z12,
model 910.13/63 with code CB8 IT4 A50, except code CB4 CB7 ME0, RG8, Z12

Model 910.1/6 with code A50 CB8 IT3, except code CB4 CB7 ME0, RG8, Z12,
model 910.1/6 with code A50 CB8 IT4 CB4, except code CB7 ME0 RG8, Z12

BE40.20-N-1001-07TSF

Total toe

Permissible difference in front axle toe between right and left sides of vehicle

°

0° 05'

0° 05'

Maximum tolerance

°

0° 10'

0° 10'

Front axle toe

Number

Designation

Model 910.0 with code A50, IT3, except code RG8,
model 910.0 with code A50, IT4, except code RG8,
model 910.0 with code IT3, RG8,
model 910.0 with code IT4, RG8,
model 910.1 with code CB4, IT3, except code CB7, CB8, RG8, Z12,
model 910.1 with code CB4, IT4, except code CB7, CB8, RG8, Z12

Model 910.1/6 with code IT3, RG8, except code CB4, CB7, CB8, ME0, Z12,
model 910.1/6 with code IT4, RG8, except code CB7, ME0, Z12,
model 910.1/6 with code IT3, Z12, except code A50, CB4, CB7, CB8, ME0,
model 910.1/6 with code IT4, Z12, except code A50, CB4, CB7, CB8, ME0

BE40.20-N-1001-07TSF

Total toe

Permissible difference in front axle toe between right and left sides of vehicle

°

0° 05'

0° 05'

Maximum tolerance

°

0° 10'

0° 10'

Front axle toe

Number

Designation

Model 910.633 with code IT3 ME0,
model 910.633 with code IT4, ME0

BE40.20-N-1001-07TSF

Total toe

Permissible difference in front axle toe between right and left sides of vehicle

°

0° 05'

Maximum tolerance

°

0° 10'

Front axle toe

Number

Designation

Model 910.121/621 with code IT3, except CB4, CB8, RG8, Z12,
model 910.123/623 with code A50, CB7, IT3, except code CB4, CB8, RG8, Z12,
model 910.123/623 with code IT3, except code A50, CB4, CB8, RG8, Z12,
model 910.131/631 with code IT4, except CB4, CB8, RG8, Z12,
model 910.133/633 with code A50, CB7, IT4, except code CB4, CB8, ME0, RG8, Z12,
model 910.133/633 with code IT4, except code A50, CB4, CB8, ME0, RG8, Z12

BE40.20-N-1002-07TSF

Toe per wheel

Angle of front axle shaft 1.80° / front axle load 1750 kg

Specified value (Actual values outside tolerance)

°

-0° 33' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 33' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 38'

Angle of front axle shaft 2.50° / front axle load 1690 kg

Specified value (Actual values outside tolerance)

°

-0° 27' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 27' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 32'

Angle of front axle shaft 3.10° / front axle load 1630 kg

Specified value (Actual values outside tolerance)

°

-0° 22' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 22' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 27'

Angle of front axle shaft 3.80° / front axle load 1570 kg

Specified value (Actual values outside tolerance)

°

-0° 16' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 16' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 21'

Angle of front axle shaft 4.40° / front axle load 1510 kg

Specified value (Actual values outside tolerance)

°

-0° 11' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 11' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 16'

Angle of front axle shaft 5.00° / front axle load 1450 kg

Specified value (Actual values outside tolerance)

°

-0° 06' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 06' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 11'

Angle of front axle shaft 5.60° / front axle load 1390 kg

Specified value (Actual values outside tolerance)

°

-0° 01' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 01' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 06'

Angle of front axle shaft 6.30° / front axle load 1330 kg

Specified value (Actual values outside tolerance)

°

0° 04' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

0° 04' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 01'

Angle of front axle shaft 6.90° / front axle load 1270 kg

Specified value (Actual values outside tolerance)

°

0° 09' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

0° 09' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

0° 04'

Angle of front axle shaft 7.50° / front axle load 1210 kg

Specified value (Actual values outside tolerance)

°

0° 13' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

0° 13' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

0° 08'

Front axle toe

Number

Designation

Model 910.123/623 with code A50 IT3, except code CB4 CB7 CB8, RG8, Z12,
model 910.133/633 with code A50 IT4 CB4, except code CB7 CB8 ME0, RG8, Z12

BE40.20-N-1003-07TSF

Toe per wheel

Angle of front axle shaft 1.80° / front axle load 1850 kg

Specified value (Actual values outside tolerance)

°

-0° 33' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 33' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 38'

Angle of front axle shaft 2.50° / front axle load 1790 kg

Specified value (Actual values outside tolerance)

v

-0° 27' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 27' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 32'

Angle of front axle shaft 3.10° / front axle load 1730 kg

Specified value (Actual values outside tolerance)

°

-0° 22' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 22' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 27'

Angle of front axle shaft 3.80° / front axle load 1670 kg

Specified value (Actual values outside tolerance)

°

-0° 16' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 16' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 21'

Angle of front axle shaft 4.40° / front axle load 1610 kg

Specified value (Actual values outside tolerance)

°

-0° 11' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 11' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 16'

Angle of front axle shaft 5.10° / front axle load 1550 kg

Specified value (Actual values outside tolerance)

°

-0° 05' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 05' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 11'

Angle of front axle shaft 5.70° / front axle load of 1490 kg

Specified value (Actual values outside tolerance)

°

0° 00' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

0° 00' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 05'

Angle of front axle shaft 6.30° / front axle load 1430 kg

Specified value (Actual values outside tolerance)

°

0° 05' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

0° 05' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

0° 00'

Angle of front axle shaft 6.90° / front axle load 1370 kg

Specified value (Actual values outside tolerance)

°

0° 09' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

0° 09' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

0° 04'

Angle of front axle shaft 7.50° / front axle load 1310 kg

Specified value (Actual values outside tolerance)

°

0° 14' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

0° 14' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

0° 09'

Front axle toe

Number

Designation

Model 910.12/62 with code CB8 IT3, except code A50 CB4 CB7, RG8, Z12,
model 910.13/63 with code CB8 IT4 A50, except code CB4 CB7 ME0, RG8, Z12

BE40.20-N-1004-07TSF

Toe per wheel

Angle of front axle shaft 1.80° / front axle load 1750 kg

Specified value (Actual values outside tolerance)

°

-0° 30' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 30' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 35'

Angle of front axle shaft 2.40° / front axle load 1690 kg

Specified value (Actual values outside tolerance)

°

-0° 25' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 25' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 30'

Angle of front axle shaft 3.00° / front axle load 1630 kg

Specified value (Actual values outside tolerance)

°

-0° 20' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 20' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 25'

Angle of front axle shaft 3.50° / front axle load 1570 kg

Specified value (Actual values outside tolerance)

°

-0° 15' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 15' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 20'

Angle of front axle shaft 4.10° / front axle load 1510 kg

Specified value (Actual values outside tolerance)

°

-0° 10' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 10' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 15'

Angle of front axle shaft 4.70° / front axle load 1450 kg

Specified value (Actual values outside tolerance)

°

-0° 06' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 06' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 11'

Angle of front axle shaft 5.20° / front axle load 1390 kg

Specified value (Actual values outside tolerance)

°

-0° 01' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 01' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 06'

Angle of front axle shaft 5.80° / front axle load 1330 kg

Specified value (Actual values outside tolerance)

°

0° 04' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

0° 04' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 01'

Angle of front axle shaft 6.40° / front axle load 1270 kg

Specified value (Actual values outside tolerance)

°

0° 08' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

0° 08' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

0° 03'

Angle of front axle shaft 7.00° / front axle load 1210 kg

Specified value (Actual values outside tolerance)

°

0° 13' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

0° 13' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

0° 08'

Front axle toe

Number

Designation

Model 910.1/6 with code A50 CB8 IT3, except code CB4 CB7 ME0, RG8, Z12,
model 910.1/6 with code A50 CB8 IT4 CB4, except code CB7 ME0 RG8, Z12

BE40.20-N-1005-07TSF

Toe per wheel

Angle of front axle shaft 0.90° / front axle load 1850 kg

Specified value (Actual values outside tolerance)

°

-0° 31' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 31' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 36'

Angle of front axle shaft 1.50° / front axle load 1790 kg

Specified value (Actual values outside tolerance)

°

-0° 26' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 26' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 31'

Angle of front axle shaft 2.00° / front axle load 1730 kg

Specified value (Actual values outside tolerance)

°

-0° 21' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 21' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 26'

Angle of front axle shaft 2.60° / front axle load 1670 kg

Specified value (Actual values outside tolerance)

°

-0° 16' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 16' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 21'

Angle of front axle shaft 3.20° / front axle load 1610 kg

Specified value (Actual values outside tolerance)

°

-0° 11' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 11' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 16'

Angle of front axle shaft 3.70° / front axle load 1550 kg

Specified value (Actual values outside tolerance)

°

-0° 06' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 06' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 11'

Angle of front axle shaft 4.30° / front axle load 1490 kg

Specified value (Actual values outside tolerance)

°

-0° 01' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 01' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 06'

Angle of front axle shaft 4.90° / front axle load 1430 kg

Specified value (Actual values outside tolerance)

0° 04' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

0° 04' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

-0° 01'

Angle of front axle shaft 5.40° / front axle load 1370 kg

Specified value (Actual values outside tolerance)

°

0° 08' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

0° 08' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

0° 03'

Angle of front axle shaft 6.00° / front axle load 1310 kg

Specified value (Actual values outside tolerance)

°

0° 13' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

0° 13' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

0° 08'

Front axle toe

Number

Designation

Model 910.0 with code A50, IT3, except code RG8,
model 910.0 with code A50, IT4, except code RG8,
model 910.0 with code IT3, RG8,
model 910.0 with code IT4, RG8,
model 910.1 with code CB4, IT3, except code CB7, CB8, RG8, Z12,
model 910.1 with code CB4, IT4, except code CB7, CB8, RG8, Z12

BE40.20-N-1006-07TSF

Toe per wheel

Angle of front axle shaft 1.80° / front axle load 1850 kg

Specified value (Actual values outside tolerance)

°

-0° 30' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 30' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 35'

Angle of front axle shaft 2.40° / front axle load 1790 kg

Specified value (Actual values outside tolerance)

°

-0° 25' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 25' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 30'

Angle of front axle shaft 3.00° / front axle load 1730 kg

Specified value (Actual values outside tolerance)

°

-0° 20' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 20' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 25'

Angle of front axle shaft 3.50° / front axle load 1670 kg

Specified value (Actual values outside tolerance)

°

-0° 15' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 15' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 20'

Angle of front axle shaft 4.10° / front axle load 1610 kg

Specified value (Actual values outside tolerance)

°

-0° 10' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 10' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 15'

Angle of front axle shaft 4.70° / front axle load 1550 kg

Specified value (Actual values outside tolerance)

°

-0° 06' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 06' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 11'

Angle of front axle shaft 5.20° / front axle load 1490 kg

Specified value (Actual values outside tolerance)

°

-0° 01' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 01' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 06'

Angle of front axle shaft 5.80° / front axle load 1430 kg

Specified value (Actual values outside tolerance)

°

0° 04' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

0° 04' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 01'

Angle of front axle shaft 6.40° / front axle load 1370 kg

Specified value (Actual values outside tolerance)

°

0° 08' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

0° 08' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

0° 03'

Angle of front axle shaft 7.00° / front axle load 1310 kg

Specified value (Actual values outside tolerance)

°

0° 13' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

0° 13' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

0° 08'

Front axle toe

Number

Designation

Model 910.1/6 with code IT3, RG8, except code CB4, CB7, CB8, ME0, Z12,
model 910.1/6 with code IT4, RG8, except code CB7, ME0, Z12,
model 910.1/6 with code IT3, Z12, except code A50, CB4, CB7, CB8, ME0,
model 910.1/6 with code IT4, Z12, except code A50, CB4, CB7, CB8, ME0

BE40.20-N-1007-07TSF

Toe per wheel

Angle of front axle shaft 2.50° / front axle load 2000 kg

Specified value (Actual values outside tolerance)

°

-0° 28' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 28' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 33'

Angle of front axle shaft 3.00° / front axle load 1940 kg

Specified value (Actual values outside tolerance)

°

-0° 23' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 23' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 28'

Angle of front axle shaft 3.50° / front axle load 1880 kg

Specified value (Actual values outside tolerance)

°

-0° 19' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 19' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 24'

Angle of front axle shaft 4.10° / front axle load 1820 kg

Specified value (Actual values outside tolerance)

°

-0° 15' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 15' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 20'

Angle of front axle shaft 4.60° / front axle load 1760 kg

Specified value (Actual values outside tolerance)

°

-0° 11' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 11' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 16'

Angle of front axle shaft 5.10° / front axle load 1700 kg

Specified value (Actual values outside tolerance)

°

-0° 07' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 07' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 12'

Angle of front axle shaft 5.70° / front axle load 1640 kg

Specified value (Actual values outside tolerance)

°

-0° 03' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 03' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 08'

Angle of front axle shaft 6.20° / front axle load 1580 kg

Specified value (Actual values outside tolerance)

°

0° 01' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

0° 01' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 04'

Angle of front axle shaft 6.70° / front axle load 1520 kg

Specified value (Actual values outside tolerance)

°

0° 05' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

0° 05' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

0° 00'

Angle of front axle shaft 7.30° / front axle load 1460 kg

Specified value (Actual values outside tolerance)

°

0° 09' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

0° 09' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

0° 04'

Front axle toe

Number

Designation

Model 910.633 with code IT3 ME0,
model 910.633 with code IT4, ME0

BE40.20-N-1008-07TSF

Toe per wheel

Angle of front axle shaft 4.70° / front axle load 1750 kg

Specified value (Actual values outside tolerance)

°

-0° 26' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 26' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 31'

Angle of front axle shaft 5.20° / front axle load 1690 kg

Specified value (Actual values outside tolerance)

°

-0° 22' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 22' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 27'

Angle of front axle shaft 5.70° / front axle load 1630 kg

Specified value (Actual values outside tolerance)

°

-0° 17' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 17' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 22'

Angle of front axle shaft 6.30° / front axle load 1570 kg

Specified value (Actual values outside tolerance)

°

-0° 14' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 14' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 19'

Angle of front axle shaft 6.80° / front axle load 1510 kg

Specified value (Actual values outside tolerance)

°

-0° 10 (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 10 (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 15'

Angle of front axle shaft 7.40° / front axle load 1450 kg

Specified value (Actual values outside tolerance)

°

-0° 06 (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 06 (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 11'

Angle of front axle shaft 7.90° / front axle load 1390 kg

Specified value (Actual values outside tolerance)

°

-0° 02 (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

-0° 02 (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 07'

Angle of front axle shaft 8.40° / front axle load 1330 kg

Specified value (Actual values outside tolerance)

°

0° 02' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

0° 02' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

-0° 03'

Angle of front axle shaft 9.00° / front axle load 1270 kg

Specified value (Actual values outside tolerance)

°

0° 06' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

0° 06' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

0° 01'

Angle of front axle shaft 9.50° / front axle load 1210 kg

Specified value (Actual values outside tolerance)

°

0° 09' (05')

Specified value (Actual values within tolerance, wear to tire outside shoulder)

°

0° 09' (05')

Specified value (Actual values within tolerance, stronger wear to tire outside shoulder)

°

0° 04'

 Steering linkage

Number

Designation

Model 907, 910

BA46.40-N-1001-06TS

Counternut, tie rod to ball head

Nm

65