T26.10-0018-09
Shown on transmission without hydrodynamic retarder R115 (integrated), Voith |
1 | Drive shaft bearing cap | 16 | Shift forks | |
5 | Drive shaft | 17 | Shift rails | |
8 | Countershaft bearing cap | 18 | Countershaft | |
9 | Countershaft shim | 19 | Main shaft | |
11 | Front transmission housing | 20 | Rear transmission housing | |
13 | Shift | 26 | Rear transmission cover | |
15 | Sliding yoke | 35 | Reverse gearwheel |
Danger ! | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. | |
| Disassemble | ||
1 | Drain transmission oil | ||
| |||
2 | Remove the transmission | See information provided by vehicle manufacturer or transmission manufacturer. | |
3 | Detach clutch housing from front transmission housing (11) | Only on front transmission housing (11) without integrated clutch housing. | |
4 | Detach hydrodynamic retarder from transmission |
| |
Transmission 714.140/143 in model 000.001Transmission with hydrodynamic retarder R115 E (integrated), Voith- 153.000452xx | |||
5 | Attach transmission to assembly device | ||
6 | Remove gearshift system (13) |
| |
Transmission 714.140/143 in model 000.001Transmission with electropneumatic power shift (EPS) | |||
7 | Remove rear transmission housing (20) | ||
8 | Remove shift forks (16) and shift rails (17) | ||
The sliding yoke (15) can only be removed together with the main shaft (19) and the countershaft (18). | |||
9 | Remove main shaft (19), countershaft (18) and sliding yoke (15) | ||
10 | Remove drive shaft bearing cap (1) and countershaft bearing cap (8) | ||
11 | Remove drive shaft (5) | ||
12 | Remove oil screen | ||
13 | Disassemble main shaft (19) | ||
14 | Disassemble countershaft (18) | ||
15 | Disassemble drive shaft (5) | ||
16 | Disassemble rear transmission cover (26) |
| |
17 | Disassemble gearshift system (13) |
| |
Transmission 714.140/143 in model 000.001Transmission with electropneumatic power shift (EPS) | |||
18 | Disassemble drive shaft bearing cap (1) | ||
19 | Disassemble rear transmission housing (20) | ||
20 | Disassemble front transmission housing (11) | ||
21 | Remove reverse gear gearwheel (35) | ||
| Clean | ||
22 | Clean all transmission parts | ||
| Check | ||
23 | Check all transmission parts for wear and condition | If there are problems | |
| |||
Replace affected transmission part. | |||
| Assemble | ||
24 | Install reverse gear gearwheel (35) | ||
25 | Assemble front transmission housing (11) | ||
26 | Assemble rear transmission housing (20) | ||
27 | Assemble drive shaft bearing cap (1) | ||
28 | Assemble gearshift system (13) |
| |
Transmission 714.140/143 in model 000.001Transmission with electropneumatic power shift (EPS) | |||
29 | Assemble rear transmission cover (26) |
| |
30 | Assemble drive shaft (5) | ||
31 | Assemble countershaft (18) | ||
32 | Assemble main shaft (19) | ||
33 | Install oil screen | ||
34 | Install drive shaft (5) | ||
35 | Install drive shaft bearing cap (1) and countershaft bearing cap (8) | ||
Do not use any new microencapsulated bolts yet. | |||
36 | Install main shaft (19), countershaft (18) and sliding yoke (15) | ||
37 | Install shift forks (16) and shift rails (17) | ||
38 | Install gearshift system (13) | Transmission 714.140/143 in model 000.001 | |
Transmission 714.140/143 in model 000.001Transmission with "control cable" gearshift | |||
Transmission 714.140/143 in model 000.001Transmission with electropneumatic power shift (EPS) | |||
39 | Install rear transmission housing (20) | ||
The oil pipe must be installed before installing the rear transmission housing (20). | |||
40 | Remove drive shaft bearing cap (1) and countershaft bearing cap (8) again | ||
So that the preload of the bearings for the drive shaft (5), main shaft (19) and countershaft (18) can be adjusted by determining the size of the shims required. | |||
41 | Determine shim for drive shaft bearing cap (1) | ||
Shims for drive shaft bearing cap (preload for drive shaft and main shaft) | |||
Screw/bolt, strip clamp to transmission housing | |||
Strip clamp | |||
Dial gage | |||
Dial indicator holder | |||
42 | Determine countershaft shim (9) for countershaft bearing cap (8) | ||
Shims for drive shaft bearing cap (preload for drive shaft and main shaft) | |||
Screw/bolt, strip clamp to transmission housing | |||
Strip clamp | |||
Dial gage | |||
Dial indicator holder | |||
43 | Install drive shaft bearing cap (1) with determined shim and countershaft bearing cap (8) with determined countershaft shim (9) | ||
44 | Attach hydrodynamic retarder to transmission |
| |
Transmission 714.140/143 in model 000.001Transmission with hydrodynamic retarder R115 E (integrated), Voith- 153.000452xx | |||
45 | Detach transmission from assembly device | ||
46 | Attach coupling housing to front transmission housing (11) | Only on front transmission housing (11) without integrated clutch housing. | |
47 | Install transmission | See information provided by vehicle manufacturer or transmission manufacturer. | |
48 | Fill with transmission oil | ||
|
000 589 59 63 00
Strip clamp
001 589 53 21 00
Dial gage
343 589 00 40 00
Dial indicator holder
Henviste dokumenter
- ap2600g2601oha Manuel gearkasse - olieskift
- ar2630g0315oha
- ar2630g0330oha
- ar2630g100001oha
- ar2630g100002oha
- ar2630g1010oha
- ar2630g1030oha
- ar2640g2474oha
- ar2640g2477oha
- ar2640g2478oha
- ar2650g0001oha
- ar2650g0420oha
- ar2650g0460oha
- ar2650g4743oha
- ar2650g4744oha
- ar2650g4775oha
- ar2656g1000oha
- ar2660g0001oha
- ar2660g0001ohb
- ar2660g0010oha
- ar2660g6515oha
- ar2660g6515ohb
- ar4330g0064oha
- ar4330g0064ohb
- as0000z001701a Fare for personskade på grund af snitsår eller hudafskrabninger grundet skarpkantede køretøjsdele