D35.10-1124-09
Shown on model 907.633 with rear axle 741.412 with code LG7 (LED High Performance headlamps) and without code C83 (Rear axle spring for increased payload) |
1 | Rear axle | 5 | Electric line | 8 | Linkage rod | ||
2 | Propeller shaft | 6 | Spring U-bolt | 15 | Spring plate | ||
4 | Shock absorber | 7 | Nuts |
Shown on model 907 with code CB2 (Air suspension comfort suspension) and without code IT5 (5.0 tons) |
6 | Spring U-bolt |
7 | Nuts |
15 | Spring plate |
16 | Retaining plate |
17 | Counterplate |
D35.10-A002-11
D35.10-1125-09
Shown on model 907.633 with code B25 (Electric parking brake) |
5 | Electrical lines | 11 | Electrical connectors | 13 | Bracket | ||
9 | Bracket | 12 | Vent line | 14 | Brake caliper | ||
10 | Brake cables |
Danger | Risk of death from lowering vehicle when working between wheels and body. Risk of injury from pinching or crushing when working on the air suspension. | Testing and repair work between the wheel and wheel arch or in the wheel well should only be performed if the vehicle is secured using suitable support fixtures to prevent it from lowering. | |
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
Warning | Risk of injury caused by pinching or crushing when working on springs or spring bodies that are under tension | Use only approved tensioning devices; additionally screen off hazardous area if necessary. Check special tools for damage and proper operation (visual inspection). Wear protective gloves. | |
Warning | Risk of injury. Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | |
Caution | Risk of injury to skin and eyes due to handling of transmission oil. Health risk caused by swallowing transmission oil | Wear protective gloves, protective clothing and safety glasses. | |
Topical note | Information on preventing damage to electronic components due to electrostatic discharge | ||
Topical note | Notes on self-locking nuts and bolts | ||
Topical note | Notes on threaded connections fastened using a tightening angle-based tightening process | ||
| Remove/install | ||
1 | Deactivate air suspension. | Model 907 with rear axle 741 | |
Topical note | Notes on air suspension | ||
2 | Remove rear wheels. | ||
3.1 | Remove both brake calipers (14). | If rear axle is reused (1) or if only separate parts are replaced. | |
Do not disconnect brake hoses from brake calipers (14). Secure brake calipers (14) at a suitable point outside of working area. | |||
3.2 | Remove brake hoses of brake calipers (14). | If rear axle (1) is replaced as a complete part. | |
The brake calipers (14) are included in the complete part of a new rear axle (1). | |||
4 | Secure vehicle on vehicle lift. | ||
Commercially available devices/tools | |||
5.1 | Remove linkage (8) of level sensor of headlamp range adjustment. | Model 907 with code LG7 (LED High Performance headlamp) | |
5.2 | Remove linkages of air suspension level sensors. | Model 907 with code CB2 (Air suspension comfort suspension) | |
6 | Disconnect electrical connectors (11). | The number of electrical connectors (11) can vary depending on the vehicle equipment installed. Disconnect the cable tie. | |
Installation: Replace cable ties. | |||
7 | Pull bleed line (12) out of crossmember. | Unhook bleed line (12) from holder on body. | |
8.1 | Remove brake cables (10) from brake compensator lever. | Model 907 except code B25 (Electric parking brake) | |
8.2 | Unhook brake cables (10) from holder (9). | Model 907 with code B25 (Electric parking brake) | |
9 | Remove brake cables (10) from crossmember. | To do so, unclip brake cables (10). | |
Sleeve | |||
10 | Remove brake cables (10), electric lines (5) and bleed line (12). | To do so, guide brake cables (10), electric lines (5) and bleed line (12) out of holders (13). | |
The number of electric lines (5) and cable ties can vary. Disconnect the cable tie. | |||
Installation: Replace cable ties. | |||
11 | Remove propeller shaft (2) from rear axle differential. | ||
| |||
12 | Remove torsion bar linkages from longitudinal member. | If installed. | |
The torsion bar linkages remain on the stabilizer. | |||
Bolt, torsion bar linkage to longitudinal member | |||
13 | Prop up rear axle (1) using support plate and major assembly support. | ||
| 000 588 11 62 00 Major assembly mount | ||
| 000 588 10 62 00 Support plate | ||
Secure rear axle (1) against falling down using tensioning strap. | |||
Commercially available devices/tools | |||
14 | Remove spring U-bolts (6). | To do so, remove nuts (7) or clamping sleeves and take off spring U-bolts (6) together with spring plates (15). | |
Model 907 with code CB2 (Air suspension comfort suspension) | |||
Model 907 except code C83 (Rear axle spring for increased payload) except code CB2 (Air suspension comfort suspension)Nut, spring U-bolt for rear axle spring to rear axle | |||
Model 907 with code CB2 (Air suspension comfort suspension) except code C83 (Rear axle spring for increased payload)Nut, spring U-bolt for rear axle spring to rear axle | |||
Model 907.1/2 with code C83 (Rear axle spring for increased payload) model 907.6/7/8 with code C83 (Rear axle spring for increased payload) except code IT5 (5.0 tons)Nut/clamping sleeve, spring U-bolt for rear axle spring to rear axle | |||
15 | Remove retaining plates (16). | Model 907 with code CB2 (Air suspension comfort suspension) | |
16 | Remove both shock absorbers (4) from rear axle (1). | ||
17 | Remove rear axle (1). | ||
18 | Convert detachable parts. | If rear axle (1) is replaced. | |
| |||
The electric line on the right rear rpm sensor is marked at the factory with a white closing strap. | |||
ABS sensor grease | |||
| Check | ||
19 | Check rear axle differential for leak tightness. | ||
Notes on evaluating leakages | |||
If the rear axle differential is leaky, | |||
| |||
perform suitable measures to rectify the leak. | |||
After obtaining special order. | |||
20 | Install in the reverse order. | ||
| Check | ||
21 | Check oil level in rear axle differential. | ||
| Rear axle - oil change | ||
If the oil level in the rear axle differential is not correct. | |||
| |||
Correct oil level. | |||
22 | Adjust parking brake. |
|
906 589 00 14 00
Sleeve
เอกสารที่อ้างถึง
- ah0000n000101a
- ah0000n001101a
- ah0000p002001a
- ah3222n100001h
- ah5400p000101a
- ap3500d3501tsr
- ar0060d010001ts
- ar3222d600002tsr
- ar3225d0110ts
- ar3233d0009tsr
- ar4010d1100ts
- ar4110d0050ts
- ar4110d0050ts
- ar4210d0023ts
- ar4210d0080ts
- ar4220d052006ts
- ar4220d0540ts
- ar8210d0005ts
- as0000z000101a
- as0000z000201a
- as0000z001001a
- as0040z000101a
- as3222z000101a
- ws0100p0092b
- ws2600p3309b