W26.45-1195-09
1 | Cylindrical roller bearing (only for transmission 715.35/37/38/5) | 15 | Housing cover (with power take-off 123-10c) | 30 | Seal | ||
2 | Housing cover | 16 | Housing cover (with power take-off 123-10b) | 31 | Slide ring | ||
3 | Cylindrical roller bearing | 17 | Radial shaft sealing ring (with power take-off 123-10b) | 32 | Sealing ring | ||
4 | Cylindrical roller bearing inner race | 18 | Output flange (with power take-off 123-10b) | 33 | Piston with shift rod | ||
5 | Output shaft (with power take-off 123-10b) | 19 | Pressure plate (with power take-off 123-10b) | 34 | Drain screw | ||
6 | Output shaft (with power take-off 123-10c) | 20 | Housing cover | 35 | Shift fork | ||
7 | Oil pipe | 21 | Shim | 36 | Compression spring | ||
8 | Housing | 22 | Centering ring | 37 | Jack | ||
8.1 | Screw | 23 | Retaining ring | 38 | Sliding sleeve | ||
9 | Seal | 24 | Ball bearing | 39 | Driver | ||
10 | Shim (with power take-off 123-10c) | 25 | Shim | 40 | Cluster gear | ||
11 | Ball bearing | 26 | Screw plug | 41 | Needle roller bearing | ||
12 | Retaining ring (with power take-off 123-10c) | 27 | Control plunger | 42 | Needle roller bearing | ||
13 | Centering ring | 28 | O-ring | 43 | Drive shaft | ||
14 | Shim | 29 | Shift cylinder with solenoid valve | S23 | Power take-off 1 indicator switch |
Warning | Risk of injury. Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | |
Topical note | Notes on self-locking nuts and bolts | ||
| Assemble | ||
1 | Check oil pipe (7) for unrestricted flow, clean if necessary | ||
2 | Install oil pipe (7) in housing (8) | ||
3 | Screw in screw plugs (26) using new sealing rings | ||
4 | Install ball bearing (24) using a suitable drift | ||
5 | Install ball bearing (11) using a suitable drift | ||
6 | Assemble (43) drive shaft | ||
Axial play of bearing on drive shaft | |||
7 | Install inner race of ball bearing (24) | | |
Heat inner race of ball bearing (24) to approx. 80 °C and install using suitable drift. | |||
8 | Attach circlip (23) to the drive shaft (43) | ||
9 | Install cylindrical roller bearing inner race (4) of output shaft (5 or 6) | Heat cylindrical roller bearing inner race (4) to approx. 80 °C and install all the way. | |
10 | Determine thickness of shim (10) on the output shaft (6) | Only with power take-off 123-10c. | |
Axial play of bearing on output shaft | |||
11 | Mount shim (10) on output shaft (6) | Only with power take-off 123-10c. | |
12 | Install output shaft (5 or 6) | Heat inner race of ball bearing (11) to approx. 80 °C and install output shaft (5 or 6) using a suitable drift. | |
13 | Install circlip (12) on output shaft (6) | Only with power take-off 123-10c. | |
14 | Install new O-rings (28) into grooves of control plunger (27) | ||
15 | Push shift fork (35) to one side and install control plunger (27) | Coat control plunger (27) with lubricant. | |
Synthetic grease 50 g | |||
16 | Insert new slide ring (31) and new sealing ring (32) in the grooves of the piston with shift rod (33) | ||
17 | Insert piston with shift rod (33) | ||
18 | Install shift cylinder with solenoid valve (29) | ||
Replace seal (30). | |||
19 | Install power take-off 1 indicator switch (S23) | Indicator switch to shift housing | |
20 | Insert push spring (36) in shift fork (35) | ||
21 | Install bush (37) in the housing cover (2) | Drift | |
22 | Install cylindrical roller bearing (3) in the housing cover (2) using a suitable drift | ||
23 | Attach housing cover (2) | Clean sealing surfaces and coat with sealant. | |
Bolt, housing cover to housing | |||
Loctite 5203 sealant | |||
24 | Install cylindrical roller bearing (1) in the housing cover (2) using a suitable drift | Only with transmission 715.35/37/38/5. | |
25 | Insert bolt (8.1) | ||
26 | Install centering rings (13 and 22) | Use a suitable drift. | |
27 | Place new seal (9) on housing (8) | ||
28 | Adjust axial play of drive shaft (43) | ||
Axial play of drive shaft bearing in housing | |||
Strip clamp | |||
29 | Put on shim (21) | ||
30 | Mount housing cover (20) | Bolt, housing cover to housing | |
31 | Adjust axial play of output shaft (5 or 6) | ||
Axial play of output shaft bearing in housing | |||
Strip clamp | |||
32 | Fit shim (14) | ||
33.1 | Fit on housing cover (15) | With power take-off 123-10c | |
33.2 | Install housing cover (16) | With power take-off 123-10b | |
Screw/nut, housing cover to housing | |||
34 | Install radial shaft sealing ring (17) for output flange (18) | Only with power take-off 123-10b. | |
35 | Install power take-off |
| |
Transmission 715.32 |
000 589 59 63 00
Strip clamp
714 589 05 15 00
Drift