W26.45-1198-09
1 | Cylindrical roller bearing (only for transmission 715.35/37/38/5) | 19 | Thrust washer | 33 | Slide ring | ||
2 | Housing cover | 20 | Bearing housing of second output (with dual output shaft with flange) | 34 | Sealing ring | ||
3 | Cylindrical roller bearing | 21 | Seal | 35 | Piston with shift rod | ||
4 | Cylindrical roller bearing inner race | 22 | Shift housing of second output | 36 | Drain screw | ||
5 | Output shaft | 23 | Shim | 37 | Shift fork | ||
7 | Oil pipe | 24 | Centering ring | 38 | Compression spring | ||
8 | Housing | 25 | Retaining ring | 39 | Jack | ||
9 | Seal | 26 | Ball bearing | 40 | Sliding sleeve | ||
11 | Ball bearing | 27 | Shim | 41 | Driver | ||
13 | Centering ring | 28 | Screw plug | 42 | Cluster gear | ||
14 | Shim | 29 | O-ring | 43 | Needle roller bearing | ||
16 | Housing cover | 30 | Control plunger | 44 | Needle roller bearing | ||
17 | Radial shaft sealing ring | 31 | Shift cylinder with solenoid valve | 45 | Drive shaft | ||
18 | Output flange | 32 | Seal | S23 | Power take-off 1 indicator switch |
| Disassemble | ||
1 | Remove power take-off | Transmission 715.32 | |
Transmission 715.35/37/38/5 | |||
2 | Remove output flange (18) | Counterhold output flange (18) with retainer wrench. Use puller in the event of sluggishness. | |
Retainer wrench | |||
Puller, two-arm | |||
3 | Detach housing cover (16) and remove shim (14) | ||
4 | Remove radial shaft sealing ring (17) for output flange (18) | ||
5 | Remove seal (9) | ||
6 | Unscrew power take-off 1 indicator switch (S23) | ||
7 | Detach housing cover (2) | When installing new housing cover (2), also install new cylindrical pins. | |
8 | Remove cylindrical roller bearing (1) | Only with transmission 715.35/37/38/5. | |
Internal extractor | |||
Countersupport | |||
9 | Remove cylindrical roller bearing (3) | Internal extractor | |
Countersupport | |||
10 | Remove bushing (39). | Internal extractor | |
Counter stay | |||
11 | Remove push spring (38) from shift fork (37) | ||
12 | Remove shit cylinder with solenoid valve (31) | ||
13 | Remove piston with shift rod (35) | ||
14 | Remove slide ring (33) and sealing ring (34) from piston with shift rod (35) | ||
15 | Push shift fork (37) to one side and remove control plunger (30) | ||
16 | Remove O-rings (29) from control plunger (30) | ||
17 | Drive out output shaft (5) using aluminum drift | ||
18 | Remove cylinder bearing inner race (4) from output shaft (5) | Puller | |
19 | Remove circlip (25) | ||
20 | Drive out input shaft (45) using aluminum drift | ||
21 | Disassemble drive shaft (45) | ||
22 | Drive out ball bearing (26) and centering ring (24) using suitable drift | ||
23 | Drive out ball bearing (11) and centering ring (13) using suitable drift | ||
24 | Unscrew screw plugs (28) and remove sealing rings | ||
25 | Remove oil pipe (7) from housing (8) | ||
26 | Disassemble bearing housing for second PTO (20) | Only with double output shaft with flange. | |
Internal extractor | |||
Counter stay | |||
27 | Disassemble shift housing of second PTO (22) | ||
28 | Assemble power take-off |
000 589 29 33 00
Internal extractor
000 589 33 33 00
Counter stay
001 589 19 33 00
Puller
000 589 35 33 00
Countersupport
000 589 68 33 00
Internal extractor
000 589 34 33 00
Counter stay
717 589 00 31 00
Retainer wrench
000 589 25 33 00
Internal extractor
000 589 88 33 00
Puller, two-arm