Modification notes |
14.09.2017 | Special tool W 716 589 05 33 00 Two-arm internal extractor removed and replaced by W 000 589 28 33 00 Puller Ø 2837 mm and W 000 589 33 33 00 Counter stay. | Operation step 9 | |
14.09.2017 | Special tool W 716 589 00 15 00 Drift removed and replaced by W 210 589 03 15 00 Drift. | Operation step 16 |
1 | Rear section of transmission housing |
2 | Bearing |
3 | Bearing |
4 | Locking plates |
5 | Bolts |
6 | Bearing sleeve |
7 | Radial shaft sealing ring |
8 | Radial shaft sealing ring |
D26.40-1168-06
Topical note | Notes on self-locking nuts and bolts | ||
| Remove | ||
1 | Remove transmission |
| |
Transmission 711.670 in model 204 with engine 642, 651 | |||
Transmission 711.651 in model 906.1/2/6/7 with engine 646.984/985/986/989/990 | |||
2 | Attach transmission to assembly stand | ||
3 | Disassemble transmission housing | ||
4 | Remove rear section of transmission housing (1) | ||
| Disassemble | ||
5 | Remove reverse idler shaft with reverse gear |
| |
Transmission 711.660 in model 906.1/2/6/7 with engine 642.992, 646.985/986/989/990 | |||
6 | Remove radial shaft sealing ring (8) | | |
7 | Remove locking washers (4) | To do this, remove the bolts (5). | |
8 | Remove bearing (3) | Sleeve | |
9 | Remove bearing (2) | To attach the internal extractor, two opposed recesses are made in the area of the bearing seat. | |
Puller, 28-37 mm dia. | |||
Counter stay | |||
10 | Remove bushing (6) | Internal extractor | |
Counter stay | |||
11 | Remove radial shaft sealing ring (7) | | |
| Clean | ||
12 | Clean seats and bearing seats | Use clean, lint-free rag. | |
| Assemble | ||
13 | Press in bearing (3) as far as the end stop in the rear section of the transmission housing (1) | Transmission 711.670 in model 204 with engine 642, 651 | |
The chamfer (arrow) on the bearing race must point towards the main shaft. | |||
Drift | |||
14 | Press in bearing (2) as far as the end stop | The inscription on the bearing (2) must point towards the countershaft. | |
Drift | |||
15 | Press in bearing bushing (6) as far as the end stop | Drift | |
16 | Press-in radial shaft sealing ring (8) up to end stop | Drift | |
17 | Drive in radial shaft sealing ring (7) flush to surface | Drift | |
18 | Coat sealing lips of radial shaft sealing ring (7, 8) with transmission oil | ||
| FE manual transmission oil (specification 235.3) | ||
| Gear oils (Sheet 235.10) | ||
19 | Install lock washers (4) | Screw/bolt, locking plate for countershaft bearing, main shaft bearing or drive shaft bearing to transmission housing | |
20 | Install reverse idler shaft with reverse gear |
| |
Transmission 711.651 in model 906.1/2/6/7 with engine 646.984/985/986/989/990 | |||
Mounting bolt, reverse idler shaft to transmission housing | |||
| Install | ||
21 | Install rear section of transmission housing (1) | ||
22 | Attach gear set with rear section of transmission housing (1) to assembly stand | ||
23 | Assemble transmission housing | ||
24 | Install transmission |
| |
Transmission 711.670 in model 204 with engine 642, 651 | |||
Transmission 711.651 in model 906.1/2/6/7 with engine 646.984/985/986/989/990 |
000 589 25 33 00
Internal extractor
000 589 28 33 00
Puller, 28-37 mm dia.
716 589 00 15 00
Drift
716 589 01 33 00
Sleeve
711 589 04 15 00
Drift
000 589 33 33 00
Counter stay
210 589 02 15 00
Drift
716 589 03 15 00
Drift
210 589 03 15 00
Drift