AR14.40-W-2010C | Remove/install SCR tank heater solenoid valve | 13.12.11 |
ENGINES 900.9 in MODEL 375.1, 970, 972, 975, 976 with CODE (MS4) BlueTec 4
ENGINES 900.9 in MODEL 375.1, 970, 972, 975, 976 with CODE (MS5) BlueTec 5
ENGINES 902.9 in MODEL 375.3, 950.5 /6, 952.5 /6, 953.6, 954.5, 957 with CODE (MS4) BlueTec 4
ENGINES 902.9 in MODEL 375.3, 950.5 /6, 952.5 /6, 953.6, 954.5, 957 with CODE (MS5) BlueTec 5
ENGINES 902.9 in MODEL 375.1, 970, 972, 974, 975, 976 with CODE (MS4) BlueTec 4
ENGINES 902.9 in MODEL 375.1, 970, 972, 974, 975, 976 with CODE (MS5) BlueTec 5
ENGINES 924.9 in MODEL 958.0, 970, 972, 974, 975, 976 with CODE (MS4) BlueTec 4
ENGINES 924.9 in MODEL 958.0, 970, 972, 974, 975, 976 with CODE (MS5) BlueTec 5
ENGINES 925.9 in MODEL 970, 972, 974 with CODE (MS4) BlueTec 4
ENGINES 925.9 in MODEL 970, 972, 974 with CODE (MS5) BlueTec 5
ENGINES 926.9 in MODEL 950.5 /6, 952.5 /6, 953.6, 954.5, 957, 958.2 with CODE (MS4) BlueTec 4
ENGINES 926.9 in MODEL 950.5 /6, 952.5 /6, 953.6, 954.5, 957, 958.2 with CODE (MS5) BlueTec 5
ENGINES 926.9 in MODEL 958.0 with CODE (MS4) BlueTec 4
ENGINES 926.9 in MODEL 958.0 with CODE (MS5) BlueTec 5
W14.40-1239-06
Shown on model 950
1 Coolant line (feed line from engine)
2 Electrical connector
3 Coolant inlet
4 Coolant outlet
5 Coolant line (feed line to pump module)
Y107 SCR tank heater solenoid valve
| Remove/install | ||
1 | Switch off ignition | ||
2 | Open maintenance flap | ||
Danger! | Risk of injury to skin and eyes caused by scalding from contact with hot coolant spray. Risk of poisoning caused by swallowing coolant. | Do not open cooling system unless coolant temperature is below 90°C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers. Wear protective gloves, protective clothing and safety glasses. | |
3 | Release pressure in coolant circuit | ||
| Notes on coolant | ||
Danger! | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure with the safety strut. | |
4 | Tilt cab | Installation: Only tilt cab back after leak test has been conducted. | |
| Notes on tilting the cab | ||
5 | Disconnect electrical connector (2) | Installation: Replace removed cable tie. | |
6 | Drain partially coolant at radiator | ||
7 | Detach coolant lines (1, 5) at SCR tank heater solenoid valve (Y107) | Collect coolant in clean container. | |
Installation: Pour caught coolant back into coolant circuit after installation of SCR tank heater solenoid valve (Y107). | |||
8 | Remove SCR tank heater solenoid valve (Y107) | | |
9 | Install in the reverse order | ||
10 | Check coolant level, pour in coolant if necessary | If the antifreeze in the coolant is too low, either add more antifreeze or change the coolant. | |
| |||
Danger! | Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near the engine as it is running | Secure vehicle to prevent it from moving by itself. | |
11 | Start engine | ||
12 | Inspecting cooling system for leaks |
Exhaust aftertreatment
Number | Designation | Engine | |||
BA14.40-N-1012-02C | SCR tank heater solenoid valve on bracket | Nm | 25 | ||
Engine cooling system
Number | Designation | Engine 900.9 in model 375.1, 970, 972, 975, 976 | Engine 902.9 in model 375.3, 950, 952, 953, 954 without code BA1 | Engine 902.9 in model 950, 952, 953, 954 with code BA1 | ||
BF20.00-N-1001-01C | Coolant | Total filling capacity | l | 19 | 22 | 37.0 |
Anticorrosion/antifreeze agent down to -37°C | L | 9.5 | 11 | 18.5 | ||
Anticorrosion/antifreeze agent down to -45°C | L | 10.5 | 12.0 | 20.5 | ||
Specifications for Operating Fluids | Sheet | |||||
Sheet | ||||||
Sheet | ||||||
Engine cooling system
Number | Designation | Engine 902.9, in model 375.1, 970, 972, 974, 975, 976 | Engine | Engine 924.9 in models 958.0, 970, 972, 974, 975, 976 | ||
BF20.00-N-1001-01C | Coolant | Total filling capacity | l | 23 | 48 | 19 |
Anticorrosion/antifreeze agent down to -37°C | L | 11.5 | 24 | 9.5 | ||
Anticorrosion/antifreeze agent down to -45°C | L | 13.0 | 26.5 | 10.5 | ||
Specifications for Operating Fluids | Sheet | |||||
Sheet | ||||||
Sheet | – | |||||
Engine cooling system
Number | Designation | Engine 925.9 in models 970, 972, 974 | Engine 926.9 in models 950, 952, 953, 954, 958.2 without code BA1 or BA9 | Engine 926.9 in models 950, 952, 953, 954, 958.2 with code BA1 | ||
BF20.00-N-1001-01C | Coolant | Total filling capacity | l | 23.0 | 22 | 37 |
Anticorrosion/antifreeze agent down to -37°C | L | 11.5 | 11 | 18.5 | ||
Anticorrosion/antifreeze agent down to -45°C | L | 13.0 | 12.0 | 20.5 | ||
Specifications for Operating Fluids | Sheet | |||||
Sheet | ||||||
Sheet | ||||||
Engine cooling system
Number | Designation | Engine 926.9 in models 950, 952, 953, 954, 958.2 | Engine 926.9 in model 957 | Engine 926.9 in model 958.0 | ||
BF20.00-N-1001-01C | Coolant | Total filling capacity | l | 40 | 48 | 23 |
Anticorrosion/antifreeze agent down to -37°C | L | 20 | 24 | 11 | ||
Anticorrosion/antifreeze agent down to -45°C | L | 22 | 26.5 | 12 | ||
Specifications for Operating Fluids | Sheet | |||||
Sheet | ||||||
Sheet | – | – | ||||