P18.00-2433-08
Shown on model 213.217 |
1 | Oil filter cover | 7 | Air intake pipe | |
2 | Oil filter element | 26 | Hoses | |
3 | Sealing ring | 27 | Locks |
Shown on model 247.014 |
1 | Oil filter cover |
2 | Oil filter element |
3 | Sealing ring |
7 | Air intake pipe |
P18.00-A002-06
Shown on model 213.213 except code M005 (Vehicles with 4-MATIC/all-wheel drive) |
15 | Drain screw |
P18.00-A004-06
Shown on model 257.319 with code M005 (Vehicles with 4MATIC/all-wheel drive) |
15 | Drain screw |
P18.00-A023-06
Shown on model 247.014 |
15 | Drain screw |
P18.00-A003-06
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
Caution | Risk of injury to skin and eyes due to handling of engine oil. Risk of poisoning caused by swallowing engine oil | Wear protective gloves, protective clothing and safety glasses. | |
Topical note | Notes on engine oil and filter changes | ||
| Remove | ||
1 | Run engine to warm it up. | Coolant temperature at least 80 °C. | |
2 | Switch off engine. | ||
3.1 | Release locks (27), remove air intake pipe (7) on air filter housing and from hoses (26) and place to the side. | Model 205, 213, 238, 253, 257 | |
Hoses(26) remain plugged on at bottom. | |||
3.2 | Remove air intake pipe (7). | Model 118, 177, 247 | |
4 | Unscrew oil filter cover (1). | Unscrew oil filter cover (1) far enough from oil filter housing so that engine oil can drain out of oil filter and oil filter housing. | |
5.1 | Remove engine compartment lining. | Model 118, 177, 247 | |
| |||
5.2 | Remove center engine compartment lining. | Model 205, 213, 238, 253, 257 with code M005 (Vehicles with 4MATIC/all-wheel drive) | |
| Model 205, 253 | ||
| Model 213, 238 | ||
| Model 257 | ||
5.3 | Remove engine compartment lining at rear. | Model 205, 213, 238, 253, 257 except code M005 (Vehicles with 4MATIC/all-wheel drive) | |
| Model 205, 253 | ||
| Model 213, 238 | ||
| Model 257 | ||
6 | Remove drain screw (15) from oil pan and drain engine oil. | Dispose of old drain screw (15). | |
| Install | ||
7 | Screw in new drain screw (15). | Drain screw to oil pan | |
8.1 | Install engine compartment lining. | Model 118, 177, 247 | |
| |||
8.2 | Install center engine compartment lining. | Model 205, 213, 238, 253, 257 with code M005 (Vehicles with 4MATIC/all-wheel drive) | |
| Model 205, 253 | ||
| Model 213, 238 | ||
| Model 257 | ||
8.3 | Install rear engine compartment lining. | Model 205, 213, 238, 253, 257 except code M005 (Vehicles with 4MATIC/all-wheel drive) | |
| Model 205, 253 | ||
| Model 213, 238 | ||
| Model 257 | ||
9 | Remove oil filter cover (1). | ||
10 | Replace oil filter element (2). | ||
11 | Replace sealing ring (3). | ||
12 | Tighten oil filter cover (1). | Threaded cap to oil filter housing | |
13.1 | Slide air intake pipe (7) onto hoses (26) and air filter housing until locks (27) engage. | Model 205, 213, 238, 253, 257 | |
Check for correct seating of hoses(26) and guides on air intake pipe(7). | |||
13.2 | Install air intake pipe (7). | Model 118, 177, 247 | |
14 | Add engine oil. | | |
Engine oil | |||
| Check | ||
15 | Run engine until warm and check for leak tightness. | Coolant temperature at least 80 °C. | |
If the engine loses oil, | |||
| |||
determine cause and correct. | |||
After obtaining special order. | |||
16 | Check engine oil level with instrument cluster. |
| |
Model 118, 177, 247 | |||
Model 257 |