Disassemble/assemble rear-end door (left door wing)

AR72.20-S-2401E

Disassemble/assemble rear-end door (left door wing)

20.2.15

Model

447.6/7

Shown on vehicle with CODE W78 (Window in liftgate/rear-end door with wipe/wash system)

1

Rear-end door

8

Rear window

2

Passage

9

Bracket

3

Wiring harness

10

License plate lamp bracket

4

Inside door opener

11

Left inner lock at bottom of rear-end door

5

Frame seal

12

Rail

6

Guide wedge

13

Guide

7

Left inner lock at top of rear-end door

M6/10

Left rear-end door wiper motor



Remove

1

Remove rear-end door (1)

Model 447.6/7
with code W50 (Rear-end door, double-wing, 180 degrees without window)
Model 447.6/7
with code W54 (2-wing rear-end door, 270 degrees)
If necessary.

AR72.20-S-1901E

 

Disassemble/assemble

2

Remove door paneling from rear door (1)

AR72.20-S-6615E

3

Remove door foil from rear-end door (1)

AR72.20-S-4100E

 Assembly: Ensure that cavity preservation is sufficient.

If the rear door (1) is replaced or repaired:



Perform hollow cavity preservation on rear-end door (1).

AR97.20-S-1500E

4

Remove left rear-end door wiper motor (M6/10)

AR82.30-S-6551E

5

Remove left inner lock at top of rear-end door (7)

AR72.40-S-4430E

6

Remove left inner lock at bottom of rear-end door (11)

AR72.40-S-4436E

7

Remove inside door opener (4) from rear-end door (1)

8

Remove rear window (8)

MODEL 447.6/7 with CODE W78 (Window in liftgate/rear-end door with wiper/washer system)

AR67.20-S-5145EE

9

Remove license plate lamp bracket (10)

Model 447.6/7
with code W50 (Rear-end door, double-wing, 180 degrees without window)
Model 447.6/7
with code W54 (2-wing rear-end door, 270 degrees)

AR72.20-S-1010E

10

Remove license plate

11

Remove bracket (9)

12

Remove passage (2) and wiring harness (3)

 Mounting wedge

*110589035900

13

Remove guide wedge (6)

14

Remove guide (13)

15

Remove sealing frame (5)

16

Drill rivet out of strip (12) and remove strip (12)



General information on riveting

AH60.00-P-0003-01N

17

Remove door retaining strap from rear-end door (1)

Model 447.6/7
with code W54 (2-wing rear-end door, 270 degrees)

 Bracket, door catch device to door

*BA72.20-N-1010-01J

18

Remove door holder (magnetic) from rear-end door (1)

Model 447.6/7
with code W54 (2-wing rear-end door, 270 degrees)

AR72.20-S-2792E

19

Drill out rivet on mounting rail for door holder (magnetic) and remove mounting rail from rear-end door (1)



General information on riveting

AH60.00-P-0003-01N

20

Remove hinges from rear-end door (1)

Model 447.6/7
with code W50 (Rear-end door, double-wing, 180 degrees without window)
Model 447.6/7
with code W54 (2-wing rear-end door, 270 degrees)
If rear-end door (1) is removed.

AR72.20-S-2650E

21

Heat model badge with hot air blower and remove

If installed.

Attach model badge to rear-end door (1)

AR72.15-S-0001E

 Assembly: Replace model badge.

22

Remove all cable ducts, retaining clips and clamps from rear-end door (1)

23

Assemble in the reverse order



Install

24

Install rear-end door (1)

Model 447.6/7
with code W50 (Rear-end door, double-wing, 180 degrees without window)
Model 447.6/7
with code W54 (2-wing rear-end door, 270 degrees)
If rear-end door (1) is removed.

AR72.20-S-1901E



Check

25

Check electrical consumers on rear-end door (1) for proper function

 Rear-end door

Number

Designation

Model 447.6/7
with code W54 (2-wing rear-end door, 270 degrees)

BA72.20-N-1010-01J

Bracket, door catch device to door

Nm

23