ar6350p140103frx

Install rear fender complete

Typ ar · temat 63.50 · wersja 0101 · 2018-09-26

Dotyczy: Model 290

Niedostępne w języku „pl”; wyświetlono w języku Angielski.

Umiejscowienie

Grupa funkcyjna 3 Nadwozie › 63 Ściana boczna › 63.50 Błotnik tylny — Seria 290

EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.34 Ściana boczna › 35.34.35 Błotnik/ ściana boczna — Seria 290

EinPAS 35 Karoseria/ rama/ elementy domontowane › 35.37 Błotnik › 35.37.31 Błotnik tylny — Seria 290

AR63.50-P-1401-03FRX

Install rear fender complete

Model

290

Gap dimensions

Number

Designation

Model 290

BE60.00-P-1011-01KA

Rear door to side section, bottom

Dimension "H"

mm

3,5 (0,5)

For picture, see

AR60.00-P-0900-01FRX

Gap dimensions

Number

Designation

Model 290

BE60.00-P-1014-01KA

Rear fender to taillamp

Dimension "K"

mm

1 (0,5)

For picture, see

AR60.00-P-0900-01FRX

Gap dimensions

Number

Designation

Model 290

BE60.00-P-1018-01KA

Liftgate to fender

Dimension "O"

mm

3,5 (1,0)

For picture, see

AR60.00-P-0900-01FRX

Gap dimensions

Number

Designation

Model 290

BE60.00-P-1020-01KA

Side wall to bumper at rear

Dimension "Q"

mm

0,5 (0,5)

For picture, see

AR60.00-P-0900-01FRX

Install rear fender complete

129 589 03 21 00

Feeler gauge

The following operation steps are shown on the left side of the vehicle. In case of damage on the right side of the vehicle, these steps must be performed analogously.
Additional information can be found in the superordinate service document.
The safety information in the superordinate service document must be observed.

Install rear fender complete

P63.50-4307-09

1

Install rear fender (1) and fit.

2

Install rear bumper.

3

Install taillamp.

4

Install seal of rear door and tailgate.

5

Install striker eye.

6

Check gaps using feeler gauge and adjust.        

7

Fix rear fender (1) in place.

8

Remove striker eye.

9

Remove seal of rear door and tailgate.

10

Remove taillamp.

11

Remove rear bumper.

12

Drive rivet holes in rear fender (1) with Ø 6.7 mm (areas A).

13

Drill and countersink rivet holes in rear fender (1) with Ø 6.7 mm (area A2).

14

Remove rear fender (1).

15

Deburr rivet holes on rear fender (1) and body on both sides.

16

Coat insides of riveted joints with zinc dust paint (areas A, A2).

Install rear fender complete

17

Install suitable spacers on outer rear wheel well at uniform intervals (area C).



18

Apply sealant to rear outer wheel well and foam parts (areas B, C).



19

In the cross-hatched area, apply 2-component adhesive to the body (area D).


Observe pretreatment of bonding surfaces and manufacturer's specifications for drying and processing time of 2-component adhesive.


P63.50-4308-06

Install rear fender complete

P63.50-4309-09

20

Install rear fender (1) and fix in place.

21

Rivet rear fender (1) with rivets Ø 6.4x12 (areas F).

22

Rivet rear fender (1) with countersunk-head rivets Ø 6.4x14.0 (area F1).

23

Rivet rear fender (1) with rivet Ø 6.5x12.5 (area G).

24

Rear fender (1) (areas E).

25

Rear fender (1) (area H).

Install rear fender complete

P63.50-4310-09

26

Rivet rear fender (1) with Ø  6.4x12 rivet (area I).

27

Rear fender (1) (areas J).

28

Rear fender (1) (area K).

Install rear fender complete

29

Rear fender (1) (areas L).


Perform inert gas welding at intervals and allow to cool down in between. This reduces heat distortion.



30

Grind inert gas welds down flat (areas L).



31

Solder surfaces on rear fender (1) with body solder and smooth (areas L).


A basic body filler can also be used as an alternative to the restoration of the surfaces with body solder.



32

Remove solder residues and grinding dust.


P63.50-4311-05