W26.40-1002-09
1 | Primary axle cover | 12 | Intermediate shaft | |
2 | Tube screws | 13 | Secondary shaft | |
3 | Primary shaft radial sealing | 14 | Gearbox rear part | |
4 | Lock-ring | 15 | Washers | |
5 | Intermediary shaft cover | 16 | Rear to front part fixation screws | |
6 | Lock-ring | 17 | Device: Housing plate | |
7 | Lock-ring | 18 | Gasket | |
8 | Radial ball bearing | 19 | Rear part cover | |
9 | Gearbox front part | 20 | Cover screws | |
10 | Needle roller bearing | 21 | Internally manufactured tool | |
11 | Compensating washer |
| Remove | ||
1 | Remove rear part cover (19) | ||
2 | Couple the housing plate (17) at the power take-off flange; put the gearbox on vertical position over the housing plate |
| |
Mounting plate | |||
3 | Remove primary axle cover (1) |
| |
4 | Remove gearbox from vehicle |
| |
Gearbox 712.62/64, 715.054 | |||
5 | Remove lock ring (4) | It is necessary to use a new lock ring when mounting. | |
6 | Remove intermediary axle cover (5) | With the help of a lever, remove the cover from the intermediate axle (5). | |
Replace the intermediary axle cover (5) when remove it. | |||
7 | Remove the locking ring (6) and (7) | When mounting, replace lock rings. | |
8 | Remove the screws (16) | ||
9 | Remove the gearbox (9) front part |
| |
Press-off tool | |||
Hydraulic spindle | |||
Pulling device | |||
10 | Remove needle roller bearing (10) and compensating washer (11) | ||
11 | Remove the radial ball bearing (8) | With an appropriate mandrel, hit the external radial bearing race on the internal front part of the gearbox (8). | |
To install the front part of the gearbox, it is necessary to remove the radial bearing (8). | |||
| Install | ||
12 | Check the clearance of the secondary axle (13) |
| |
.Secondary shaft clearance | |||
13 | Place the previously calculated compensating washer (11) on the primary tree (13) | ||
14 | Install radial ball bearing (10) | ||
15 | Mount front part of gearbox (9) to its rear part (14) | Clean sealing surfaces and apply a sealing product. | |
Loctite sealant 518 | |||
.Front housing on the gearbox rear housing | |||
16 | Install radial bearing (8) | ||
| |||
With the aid of a mandrel, mount internal radial bearing race to its stop. | |||
Drift | |||
17 | Install new lock rings (6) and (7) | When installed, check if lock rings have the smallest possible looseness. | |
18 | Install new cover (5) on the intermediary shaft | Lubricate sealing surfaces with a sealing product. | |
Loctite sealant 518 | |||
Drift | |||
19 | Install a new lock ring (4) | ||
20 | Replace primary shaft radial sealing (3) |
| |
Drift | |||
21 | Install primary axle cover (1) |
| |
22 | Install gearbox on vehicle |
| |
Gearbox 712.62/64, 715.054 | |||
23 | Remove housing plate (17) |
| |
Mounting plate | |||
24 | Install cover (19) | Install a new gasket (18). | |
.Rear cover of the axle |
715 589 02 15 00
Drift
715 589 00 15 00
Drift
715 589 01 63 00
Mounting plate
715 589 01 35 00
Press-off tool
715 589 02 33 14
Hydraulic spindle
387 589 05 15 00
Drift
652 589 00 33 00
Pulling device