P20.00-2219-06
Shown on engine 135.9
1 Cooling system cap
2 Radiator
3 Drain plug on radiator
4 Expansion reservoir
5 Engine drain plug
6 Filling device
7 Adapter
Drain | |||
Danger! | Risk of injury to skin and eyes caused by scalding from contact with hot coolant spray. | Do not open cooling system unless coolant temperature is below 90°C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers. Wear protective gloves, protective clothing and safety glasses. | |
| Notes on coolant | ||
1 | Turn the cooling system cap (1) on the radiator (2) half a revolution in counterclockwise direction, release pressure relief, then unscrew cooling system cap (1). | ||
2 | Remove lower engine compartment paneling | ||
3 | Unscrew radiator drain plug (3) on radiator (2) and drain coolant | Catch coolant in a suitable vessel. | |
4 | Unscrew engine drain plug (5) on the crankcase and drain coolant | Catch coolant in a suitable vessel. | |
Filling | |||
5.1 | Tighten engine drain plug (5) with new gasket on crankcase | On engines 134.9 and 135.9 | |
| |||
5.2 | Coat engine drain plug (5) with sealing compound and screw onto crankcase | On engine 122.9 | |
| |||
| |||
Loctite 262 | |||
6 | Tighten radiator drain plug (3) on radiator (2) | ||
7 | Install lower engine compartment paneling. | ||
8 | Connect filling device (6) with adapter (7) to the radiator (2), evacuate and then fill the cooling system | Observe instruction manual from filling device (6) manufacturer. | |
| |||
| |||
| |||
9 | Screw cooling system cap (1) onto the radiator (2) | ||
| Checking | ||
Danger! | Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near the engine as it is running | Secure vehicle to prevent it from moving by itself. | |
10 | Carry out engine test run | ||
11 | Check coolant level in radiator (2) and in the expansion reservoir (4) and correct if necessary | ||
| Engine cooling system - check fluid level, adjust to correct level. Inspect anticorrosion/antifreeze protection, adjust to correct concentration |
Cylinder crankcase, timing case cover, end cover
Number | Designation | Engine | Engine 134.911 | ||
BA01.40-P-1001-01O | Coolant drain plug to crankcase | Nm | 25 | 25 | |
Cylinder crankcase, timing case cover, end cover
Number | Designation | Engine | Engine | ||
BA01.40-P-1001-01O | Coolant drain plug to crankcase | Nm | 25 | 25 | |
Cylinder crankcase, timing case cover, end cover
Cooling system
Number | Designation | Engine | Engine | Engine | ||
BF20.00-P-1001-02T | Cooling system | Total filling capacity | Liters | 6.0 | 4,2 | 4.6 |
Filling capacity of anticorrosion/ | Liters | 3,0 | 2,1 | 2,3 | ||
Filling capacity of anticorrosion/ | Liters | 3,3 | 2,3 | 2,5 | ||
Sheet | ||||||
454 589 00 91 00
Wrench socket
Adapter
Filling device
450 589 20 63 00
454 589 05 09 00
Repair materials
Number | Designation | Order number |
BR00.45-Z-1059-02A | Loctite 262 | Henkel Loctite Deutschland GmbH |
Powiązane dokumenty
- ah2000n208001a Wskazówki dotyczące płynu chłodzącego
- ap2000p2010ff
- ar6120p1105ff
- as0000z000501a Niebezpieczeństwo wypadku na skutek samoczynnego ruszenia przy pracującym silniku. Niebezpieczeństwo obrażeń na skutek zmiażdżenia lub poparzenia przy wykonywaniu czynności podczas rozruchu lub przy pracującym silniku.
- as2000z000101a Niebezpieczeństwo zranienia skóry i oczu przez poparzenie wytryskującym, gorącympłynem chłodzącym. Niebezpieczeństwo zatrucia na skutek połknięcia płynu chłodzącego