Shown on engine 471.9 |
1 | Rail |
2 | Electrical connector |
B622 | Rail pressure sensor |
W07.16-1105-11
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
Warning | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure it with the safety strut. | |
Danger | Risk of explosion caused by fuel igniting. Risk of injury to skin and eyes caused by fuel spraying out at high pressure | Keep all ignition sources out of hazard area. | |
Danger | Risk of explosion caused by fuel igniting, risk of poisoning caused by inhaling and swallowing fuel as well as risk of injury to eyes and skin caused by contactwith fuel. | No fires, sparks, open flames or smoking. Pour fuels into suitable and appropriately marked containers only. | |
Topical note | Notes on tilting the cab | ||
Topical note | Notes on avoiding damage through contamination and foreign objects | ||
Note on calculation of tightening torque when using insertion or socket tools with various effective lengths | |||
Notes on safety-relevant components | |||
| Remove/install | ||
1 | Tilt cab. | Installation: Only tilt back cab after the leak test. | |
2 | Remove noise encapsulation. | Installation: Only install soundproofing after the leak test. | |
3 | Clean engine in the area of the rail pressure sensor (B622). | ||
4 | Disconnect electrical connection (2). | ||
5 | Unscrew rail pressure sensor (B622) from rail (1). | Counterhold rail (1) at front on flange with an open end wrench. | |
Engine 470.9, engine 471.9, engine 473.9Rail pressure sensor at rail | |||
6 | Install in the reverse order | ||
| Check | ||
7 | Perform engine test run. | Allow the engine to run at a higher engine speed. | |
If engine fails to start or only runs for a brief period, | |||
| |||
fill the fuel low-pressure circuit. | |||
8 | Check area of the rail pressure sensor (B622) for leak tightness. | Visual inspection. | |
9 | Connect diagnostic system, start XENTRY and perform quick test. | ||
10 | Check the engine management for proper operation. | ||
11 | End XENTRY and remove the diagnostic system. |
Verwezen documenten
- ah0000n500001h Aanwijzingen voor voorkomen van schade door verontreinigingen
- ah0000p001501cw Aanwijzing voor berekenen van aanhaalmoment bij gebruik van insteek- of montagegereedschap met verschillende lengten
- ah0000z001901a Opmerkingen met betrekking tot veiligheidsrelevante onderdelen
- ah6080n000301a Aanwijzingen voor het kantelen van de cabine
- ar0708w100001a
- ar0716w1007h
- as0000z000501a Kans op ongevallen door spontaan wegrijden bij draaiende motor. Kans op letsel door bekneld raken en verbranding bij ingrepen tijdens het starten of bij draaiende motor.
- as0716z000101b Explosiegevaar door ontbranding van brandstofdampen. Kans op letsel aan huid en ogen door naar buiten spuitende brandstof.
- as4700z000101a Explosiegevaar door ontbranding, vergiftigingsgevaar door het inademen en binnenkrijgen van brandstof en kans op letsel door huid- en oogcontact met brandstof.
- as6080z000101a Kans op letsel door bekneld raken bij het kantelen van de cabine.