ar0145p7500a

Remove/install oil pan

유형 ar · 주제 01.45 · 버전 0122 · 2011-11-10

적용 대상: ENGINES 111.940 /960 in MODEL 124 ENGINES 111.920 /921 /941 /945 /961 /974 in MODEL 202 ENGINES 111.946 in MODEL 170 ENGINES 111.945 in MODEL 208

“ko”(으)로는 제공되지 않아 영어(으)로 표시합니다.

위치

기능 그룹 1 엔진 › 01 엔진 전체, 엔진 배기, 실린더 헤드, 실린더 크랭크케이스 › 01.45 오일팬 — 시리즈 124 · 시리즈 170 · 시리즈 202 · 시리즈 208

EinPAS 15 엔진 › 15.15 연소 엔진 전체/엔진 블럭/크랭크 어셈블리 › 15.15.43 오일 팬/필러 넥 — 시리즈 124 · 시리즈 170 · 시리즈 202 · 시리즈 208

엔진/변속기에도 적용: 111 920, 111 921, 111 940, 111 941, 111 945, 111 946, 111 960, 111 961, 111 974

AR01.45-P-7500A

Remove/install oil pan

2.11.11

ENGINES 111.940 /960 in MODEL 124

ENGINES 111.920 /921 /941 /945 /961 /974 in MODEL 202

ENGINES 111.946 in MODEL 170

ENGINES 111.945 in MODEL 208

Remove/install oil pan

P01.45-0208-09

Remove/install

1.1

Remove front axle stabilizer bar (5)

Model 124

ra32001240300x

Model 202, 208

AR32.20-P-0300C

2.1

Drain coolant

Model 170

AR20.00-P-1142HG

Notes on coolant

All engines

AH20.00-N-2080-01A

3

Drain engine oil

4.1

Loosen fan cowl (3) from brackets and lay over the fan

Vehicles with fan cowl

Installation: Adjust fan shroud (3) to fan.

5.1

Loosen radiator (16) from brackets

Model 124

to avoid damaging the radiator when lifting the engine.

6.1

Loosen top oil line (13) for power steering pump (arrow)

Model 124

to prevent strain on the oil line when lifting the engine.

7.1

Loosen the cable strap for the engine wiring harness at the right wheel well

Model 124

To prevent strain on the engine wiring harness when raising the engine.

8

Unscrew the exhaust at the exhaust manifold

AR49.10-P-7000B

9.1

Unscrew carrier for exhaust bracket on transmission

Except model 170

10

Pull out the oil level sensor plug (S43)

11

Unscrew screw/bolt (11) on the front engine mount below.

*BA22.10-P-1001-01A

12.1

Loosen coolant hose on coolant thermostat - housing

Model 170

13

Unscrew screw/bolt (12) at lower rear engine mounts

*BA22.10-P-1002-01A

14

Raise engine

Attach engine hoist (22) to front and rear engine lifting eyes and raise engine evenly at the front and rear.

Load regulator
gotis://H_00.12_04.0

15

Remove oil pan (56) together with oil gasket (56a)

Remove oil pan (56) in the direction of travel from below.

Model 202, 208: To facilitate removal of the oil pan (56):

Remove oil pump

AR18.10-P-6020HG

Installation: Clean sealing surfaces, replace oil pan gasket (56a), pay attention to varying bolt lengths and bolt diameters

Bolt plan for oil pan

AR01.45-P-7500-06HA

*BA01.45-P-1001-01A

*BA01.45-P-1002-01A

Align oil pan (56) to rear contact surface on transmission.

If the oil pan is not aligned to the transmission, this can result in noise and vibration problems.

16

Install in the reverse order

Danger!

Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near the engine as it is running

Secure vehicle to prevent it from moving by itself.
Wear closed and snug-fitting work clothes.
Do not touch hot or rotating parts.

AS00.00-Z-0005-01A

17

Check for leaks with engine running

Oil pan

Number

Designation

Engine
111.92/94/
952/956/
957/96/97/98

BA01.45-P-1001-01A

Bolt, oil pan to cylinder crankcase

M6

Nm

10

M8

Nm

25

M10

Nm

-

BA01.45-P-1002-01A

Bolt, transmission bell housing to oil pan

Nm

40

Engine suspension, engine mounts, engine supports

Number

Designation

Engine
111 in model 124

Engine 111 in
model 170, 202, 208

BA22.10-P-1001-01A

Bolt of engine mount to frame crossmember

M8

Nm

-

25

M10

Nm

40

-

BA22.10-P-1002-01A

Bolt, rear engine mount to rear engine crossmember

Nm

25

25

참조 문서