EinPAS 35 Kori/runko/liittyvät osat › 35.51 Matkustajan ovi 1 › 35.51.32 Ovilevy/ovikehys — Mallisarja 454 (mallit 0**)
EinPAS 35 Kori/runko/liittyvät osat › 35.52 Matkustajan ovi 2 › 35.52.32 Ovilevy/ovikehys — Mallisarja 454 (mallit 0**)
EinPAS 35 Kori/runko/liittyvät osat › 35.53 Matkustajan ovi 3 › 35.53.32 Ovilevy/ovikehys — Mallisarja 454 (mallit 0**)
EinPAS 35 Kori/runko/liittyvät osat › 35.54 Matkustajan ovi 4 › 35.54.32 Ovilevy/ovikehys — Mallisarja 454 (mallit 0**)
AR60.00-P-0700-01FF
Sizes of gaps at hoods, doors and covers
Test and adjustment values
Number
Designation
Model 454.0
BE60.00-P-1001-01M
Size of gap
CBS front end to headlamps
Dimension "A"
mm
5.0 (2.5)
CBS front to front engine hood
Dimension "B"
mm
5.0 (1.5)
CBS front to side engine hood
Dimension "C"
mm
8.0 (1.5)
CBS front to A-pillar
Dimension "D"
mm
5.0 (1.0)
CBS front to cover
Dimension "E"
mm
3.0 (1.0)
BE60.00-P-1002-01M
Size of gap
Engine hood to cover
Dimension "F"
mm
4.0 (2.0)
Cover to A-pillar
Dimension "G"
mm
3.0 (1.0)
BE60.00-P-1003-01M
Size of gap
Front door to A-pillar
Dimension "H"
mm
8.0 (1.5)
Front door to entry
Dimension "I"
mm
8.0 (1.5)
Front door to rear door
Dimension "J"
mm
8.0 (1.5)
BE60.00-P-1004-01M
Size of gap
Rear door entry
Dimension "K"
mm
8.0 (1,5)
Rear door to C-pillar
Dimension "L"
mm
8.0 (1,5)
BE60.00-P-1005-01M
Size of gap
CBS rear end to C-pillar
Dimension "M"
mm
5.0 (1.0)
CBS rear end to tailgate
Dimension "N"
mm
7.0 (2.0)
BE60.00-P-1006-01M
Size of gap
Rear door to C-pillar
Dimension "O"
mm
6.5 (1.0)
Rear door to taillamp
Dimension "P"
mm
7.0 (1.0)
Tailgate to side CBS rear end
Dimension "Q"
mm
6.5 (2.0)
BE60.00-P-1007-01M
Size of gap
Taillamp to rear spoiler
Dimension "R"
mm
5.4 (1.5)
Taillamp to C-pillar
Dimension "S"
mm
3.0 (1.0)
BE60.00-P-1008-01M
Size of gap
Roof to rear spoiler
Dimension "T"
mm
6.5 (2.0)
Feeler gage
452 589 01 21 00
P60.00-2311-05
Adjust hood, doors and trunk lid as shown in drawings. The gap should not run wedge-shaped or be too narrow at points. Deviations from parallel gap should be max. 1.0 mm over the entire length.
If the inside clearance is too large or too small, the movable body parts must be centered accordingly.
The reference measurements apply only for repair work on bodies damaged in accidents.
P60.00-2312-06
Adjust hood, doors and trunk lid as shown in drawings. The gap should not run wedge-shaped or be too narrow at points. Deviations from parallel gap should be max. 2.0 mm over the entire length.
If the inside clearance is too large or too small, the movable body parts must be centered accordingly.
The reference measurements apply only for repair work on bodies damaged in accidents.
