1 | Outer sliding door entrance |
S63.30-4747-06
Danger | Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC) | Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines.Model 447 with engine 780 | |
Danger | The high voltage used for electric welding presents a lethal hazard. Risk of explosion from welding in areas close to highly inflammable materials. Risk of injury from weld splatter and UV-light when welding. Risk of poisoning from inhaling welding gases | Use insulating mats. Wear protective clothing, safety glasses and a protective mask. Remove highly inflammable materials from the hazard area. Use air extraction system. | |
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
Caution | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. | |
Topical note | Special instructions for lifting and supporting vehicle | ||
Topical note | Notes on battery | ||
Topical note | General information on vehicles with high-voltage on-board electrical system and/or lithium-ion battery and/or gaseous-fuel drive system as well as personal protective equipment | Model 447 with engine 780 | |
Topical note | General information on body repair | ||
Topical note | Measures for preventing damage to components when performing electric welding and soldering work | ||
General information on MB materials | |||
| Remove | ||
1 | Remove all detachable parts in area of repair point. | ||
2 | Cover all detachable parts remaining in vehicle with welding protection blankets. | Commercially available devices/tools | |
3 | Remove soundproofing. | ||
Only in repair area. | |||
4 | Remove outer sliding door entrance (1). | ||
Commercially available devices/tools | |||
WIS Service Media | |||
Zinc dust paint suitable for spot welding | |||
5 | Prepare outer sliding door entrance (1). | ||
Commercially available devices/tools | |||
WIS Service Media | |||
Zinc dust paint suitable for spot welding | |||
| Install | ||
6 | Install and weld in outer sliding door entrance (1). | ||
| 000 588 01 84 00 Welder | ||
| 000 588 02 84 00 Welder | ||
Commercially available devices/tools | |||
WIS Service Media | |||
7 | Remove welding protection blankets. | Commercially available devices/tools | |
Danger | Risk of explosion caused by paint vapors igniting. Risk of poisoning caused by inhaling paint vapors. | No smoking! No open fire! Use respiratory protection, protective clothing, gloves, safety glasses and protective skin cream. Ensure that the area is well ventilated. | |
8 | Prime repair area with a primer filler. | ||
Topical note | Notes on paintwork repairs | ||
| |||
Use only primer filler approved by Daimler AG: | |||
9 | Seal seam after repair. | ||
Supplement standard seals with sealant. | |||
Danger | Risk of explosion caused by paint vapors igniting. Risk of poisoning caused by inhaling paint vapors. | No smoking! No open fire! Use respiratory protection, protective clothing, gloves, safety glasses and protective skin cream. Ensure that the area is well ventilated. | |
10 | Paint repair area and adjacent surfaces. | ||
Topical note | Notes on paintwork repairs | ||
Use only paints approved by Daimler AG: | |||
11 | Supplement cavity preservation. | ||
12 | Install soundproofing. | ||
Only in repair area. | |||
13 | Install all detachable parts in area of repair point. |
Referenced documents
- ah0000z030001a General information on vehicles with high-voltage on-board electrical system and/or lithium-ion battery and/or gaseous-fuel drive system as well as personal protective equipment
- ah0060n010001a Special instructions for lifting and supporting vehicle
- ah5410p000101a
- ah5410p000101a Notes on battery
- ah6000n000101a General information on body repair
- ah6000p000102a Measures for preventing damage to components when performing electric welding and soldering work
- ah9800p940802a Notes on paintwork repairs
- ah9800p940903a General information on MB materials
- ar6000s1752e Remove, install soundproofing
- ar6330s000401e Separate outer sliding door entrance
- ar6330s000402e Prepare outer sliding door entrance for welding in
- ar6330s000403e Weld in outer sliding door entry
- ar9710s4000e Seam sealing following repair
- ar9720s1500e Cavity preservation following repair work
- as0000z000701a The high voltage used for electric welding presents a lethal hazard. Risk of explosion from welding in areas close to highly inflammable materials. Risk of injury from weld splatter and UV-light when welding. Risk of poisoning from
- as0000z001001a Risk of death caused by vehicle slipping or toppling off of the lifting platform.
- as0000z001701a Risk of injury caused by scraping or cutting body parts on sharp vehicle parts
- as0000z003501a Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC)
- as9800z000201a Risk of explosion caused by paint vapors igniting. Risk of poisoning caused by inhaling paint vapors.
- ws6000p0021k 000 588 01 84 00 Welder
- ws6000p0022k 000 588 02 84 00 Welder