Shown on model 907, left side of vehicle |
D63.10-1945-06
Shown on model 907.7 with code W16 (front left window fixed in the side wall/sliding door), with code W34 (rear left sliding window ), with code V21 (Luxury interior trim), and with passenger bench seat (11), left side of the vehicle |
4 | Filler neck |
5 | Bonded side window |
6 | Front side wall trim |
7 | Rear side wall trim |
8 | Frame seal |
9 | Seat belt |
10 | Lock striker |
11 | Passenger bench seat |
D60.00-A018-06
D60.00-A039-09
Shown on model 907, left side of vehicle |
18 | Electrical wiring harness |
Danger | Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC) | Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines.Typ 910.6 mit Motor 780.703 | |
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
Topical note | Notes on battery | Typ 910.6 mit Motor 780.703 | |
Topical note | Notes on carrying out repair work in the vehicle interior | ||
| Remove/install | ||
1 | Remove fuel filler flap. | If left side of vehicle is damaged. | |
2 | Remove respective underfloor paneling. |
| |
3 | Remove respective underfloor paneling at high-voltage battery carrier. | * Applies to Europe only | |
Model 910.6 with engine 780.703 | |||
4 | Remove filler neck (4). | If left side of vehicle is damaged. | |
Model 907.6 with engine 654.9, Models 907.6/7 with engines 642, 651, Model 910.6 with engine 651 | |||
Model 907.6/7 with engine 274 | |||
5 | Remove respective protective strips. | ||
6 | Remove respective bonded front side window (5). |
| |
7 | Remove respective wheel well trim. |
| |
8 | Remove upper trim from partition. |
| |
9 | Remove lower trim from partition. |
| |
10 | Remove respective front door sill trim. | ||
11 | Remove respective passenger bench seat (11). |
| |
12 | Remove respective side load compartment trim. |
| |
13 | Remove respective front side wall trim (6). |
| |
14 | Remove respective center side wall trim. |
| |
15 | Remove respective rear side wall trim (7). |
| |
16 | Remove respective cable duct of the electrical wiring harness (18). | Model 907.6/7, 910.6 with code V94 (Cable duct on side wall) | |
17 | Remove respective electrical wiring harness (18) in the repair area and position outside the working area. | ||
18 | Remove front roof lining. | ||
19 | Remove center roof lining. |
| |
20 | Remove rear center roof lining. |
| |
21 | Remove tie-down rail from side wall. |
| |
22 | Remove front partition. | Model 907.6, 910.6 with code D50 (full-width partition wall) or with code D51 (full-width partition wall with 1 window) or with code D64 (partition with sliding door) | |
Model 910.6 with code D50 (full-width partition wall) or code D51 (full-width partition wall with 1 window) | |||
Model 907.6 with code D50 (full-width partition wall) or code D51 (full-width partition wall with 1 window) | |||
Model 907.6, 910.6 with code D64 (Partition with sliding door) | |||
23 | Remove load compartment floor. |
| |
Model 907.6, 910.6 with code V43 (Wooden floor) except code VK8 (Plastic floor covering) | |||
24 | Remove respective sealing frame (8) in repair area and position outside the working area. | ||
25 | Remove respective seat belt (9). | ||
26 | Remove respective lock striker (10). | Bolt, lock striker to B-pillar | |
27 | Install in the reverse order. |
Referenced documents
- ah5410p000101a
- ah5410p000101a Notes on battery
- ah6800n000101s Notes on carrying out repair work in the vehicle interior
- ar4710d7541ts Remove/install filler neck of fuel tank
- ar4710d7541tsc Remove/install filler neck of fuel tank
- ar6130d1001ts Remove/install underbody paneling
- ar6130d1002te Remove/install underbody trim on high-voltage battery carrier
- ar6730d2400ts Remove/install bonded side window
- ar6830d0016ts Remove/install wheel well trim
- ar6830d1185ts Remove/install side load compartment paneling
- ar6830d1208tsr Remove/install rear side wall trim in passenger compartment
- ar6830d1209tsr Remove/install front side wall trim in passenger compartment
- ar6830d1211tsr Remove/install center side wall trim in passenger compartment
- ar6830d1306ts Remove/install entrance paneling
- ar6830d1407ts Remove/install upper trim on partition
- ar6830d1408ts Remove/install lower trim on partition
- ar6830d7607ts Remove/install front headliner
- ar6830d7609tsr Remove/install center roof trim
- ar6830d7612tsr Remove/install rear center headliner
- ar6850d8250ts Remove/install tie-down rail on sidewall
- ar6874d0700tsf Remove/install front partition wall
- ar6874d0700tsr Remove/install front partition wall
- ar6880d5800tsf Remove/install load compartment floor
- ar6880d5800tsr Remove/install load compartment floor
- ar8860d6023ts Remove/install tank flap
- ar8880d1040ts Remove/install moldings
- ar9121d4425ts Remove/install passenger bench seat
- ar9140d1015ts Remove/install seat belt on B-pillar
- as0000z001001a Risk of death caused by vehicle slipping or toppling off of the lifting platform.
- as0000z003501a Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC)