Remove/install detachable parts for replacing lower part of door frame paneling

AR60.00-D-0050TSB

Remove/install detachable parts for replacing lower part of door frame paneling

14.04.2020

Model

907.6/7, 910.6

except code T16 (Sliding door right)

Right side of vehicle

Model

907.6/7, 910.6

except code T19 (Sliding door left)

Left side of vehicle

Modification notes

19.12.2019

Method extended

Step 5

Shown on model 910.6, left side of vehicle

15

Frame seal

Shown on model 907, left side of vehicle

18

Electrical wiring harness

 Danger

Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC)

Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines.Typ 910.6 mit Motor 780.703

AS00.00-Z-0035-01A

 Danger

Risk of death caused by vehicle slipping or toppling off of the lifting platform.

Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.

AS00.00-Z-0010-01A

Topical note

General information on vehicles with high-voltage on-board electrical system and/or lithium-ion battery and/or gaseous-fuel drive system as well as personal protective equipment

Typ 910.6 mit Motor 780.703

AH00.00-Z-0300-01A

Topical note

Notes on battery

Typ 910.6 mit Motor 780.703

AH54.10-P-0001-01A

Topical note

Notes on carrying out repair work in the vehicle interior

AH68.00-N-0001-01S

 

Remove/install

1

Remove respective hinge of front door.

AR72.10-D-2662TS

2

Remove respective front door sill trim.

AR68.30-D-1306TS

3

Remove fuel filler flap.

If left side of vehicle is damaged.

AR88.60-D-6023TS

4

Remove respective underfloor paneling.

Model 907.6/7 with code XM1 (Noise abatement measures), model 910.6 with engine 651 with code XM1 (Noise abatement measures), model 910.6 with engine 780.703

AR61.30-D-1001TS

5

Remove respective underfloor paneling at high-voltage battery carrier.

* Applies to Europe only

Model 910.6 with engine 780.703

AR61.30-D-1002TE

6

Remove filler neck.

If left side of vehicle is damaged.

Model 907.6 with engine 654, Models 907.6/7 with engines 642, 651, Model 910.6 with engine 651

AR47.10-D-7541TS

Model 907.6/7 with engine 274

AR47.10-D-7541TSC

7

Remove lower trim from partition.

Model 907.6, 910.6 with partition and with code VA3 (load compartment interior trim up to roof height, washable)

AR68.30-D-1408TS

8

Remove respective sealing frame (15) in the repair area and position outside of the working area.

9

Remove respective front fender.

AR88.10-D-1005TS

10

Remove respective lower front fender.

AR88.10-D-0002TS

11

Remove each front wheel.

AR40.10-D-1100TS

12

Remove respective rear section of front fender liner.

AR88.10-D-1321TS

13

Remove respective protective strips.

AR88.80-D-1040TS

14

Remove respective electrical wiring harness (18) in the repair area and position outside the working area.

15

Remove respective front floor covering.

Model 907.6/7

AR68.80-D-0006TSR

Model 910.6

AR68.80-D-0006TSF

16

Remove respective seat belt from B-pillar.

AR91.40-D-1015TS

17

Install in the reverse order.