1 | Boot |
2 | Steering shaft |
3 | Screw |
4 | Nut |
5 | Steering gear |
5.1 | Primary shaft |
A | Assembly slot |
B | Mark |
C | Mark |
W46.10-1119-01
W46.10-1120-01
2 | Steering shaft |
6 | Steering column bracket |
7 | Steering column trim |
8 | Boot |
W46.10-1118-12
Warning | Risk of injury from being trapped in the swivel range of steered axles | Ensure that no persons or objects are in the swivel range of all steered axles when turning the steering wheel. Do not stand in the swivel range of the additional steering axle when the engine is running. | |
Warning | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure with the safety strut. | |
Topical note | Notes on self-locking nuts and bolts | ||
Topical note | Notes on maintenance and repair work | ||
Topical note | Notes on tilting the cab | ||
Notes on safety-relevant components | |||
| Remove | ||
1 | Move front wheels to straight-ahead position and secure steering wheel in center | ||
2 | Secure steering wheel against turning | Fix the steering wheel in place on the support rod using e.g. cable ties. | |
3 | Open maintenance flap | ||
4 | Tilt cab | ||
5 | Detach boot (1) from steering gear (5) and slide upwards | ||
6 | Check marking (B) on primary shaft (5.1) relative to assembly slot (A) of lower universal joint of steering shaft (2) | If the assembly slot (A) has moved. | |
| |||
Mark installation position of lower universal joint relative to primary shaft (5.1). | |||
7 | Remove steering shaft (2) from steering gear (5) and fasten at side so that it is not trapped when the cab is tilted back | ||
8 | Lower cab | ||
9 | Remove boot (8) from steering column trim (7) | ||
10 | Remove steering column trim (7) | ||
11 | Detach anti-twist lock from steering wheel | ||
12 | Turn steering wheel approx. 90° to left or right so that the screw of the upper universal joint of steering shaft (2) can be removed from the steering column bracket (6) | ||
13 | Secure steering wheel against turning | Fix the steering wheel in place on the support rod using e.g. cable ties. | |
14 | Mark installation position of assembly slot at upper universal joint of steering shaft (2) relative to the steering column bracket (6) | ||
15 | Remove steering shaft (2) from steering column bracket (6) | ||
| Install | ||
16 | Fit steering shaft (2) onto steering column bracket (6) | Observe markings. | |
Fit bolt/nut, universal/constant velocity joint | |||
17 | Detach anti-twist lock from steering wheel | ||
18 | Turn steering wheel back approx. 90° and align in center | ||
19 | Secure steering wheel against turning | Fix the steering wheel in place on the support rod using e.g. cable ties. | |
20 | Install steering column trim (7) | ||
21 | Attach boot (8) to steering column trim (7) | ||
22 | Tilt cab | ||
23 | Attach steering shaft (2) to steering gear (5) | The contact surface for the screw and nut at the lower universal joint must be free of grease. Pay attention to installation position. | |
Fit bolt/nut, universal/constant velocity joint | |||
24 | Fit boot (1) onto steering gear (5) | ||
25 | Lower cab | ||
26 | Close maintenance flap | ||
27 | Detach anti-twist lock from steering wheel | ||
28 | Perform a test drive | During the test drive check whether the steering wheel is in the straight-ahead position. | |
If the steering wheel is not in the straight-ahead position. | |||
| |||
Remove steering wheel, install again in straight-ahead position. | |||
Referenced documents
- ah0000n000101a Notes on self-locking nuts and bolts
- ah0000z001901a Notes on safety-relevant components
- ah4620n000101h Notes on maintenance and repair work
- ah6080n000301a Notes on tilting the cab
- ar4610w0100a Remove/install steering wheel
- as4600z000201a Risk of injury from being trapped in the swivel range of steered axles
- as6080z000101a Risk of injury caused by body parts being pinched or crushed as cab is tilted