1 | Overflow pipe |
2 | Adapter |
P27.00-2165-04
3 | Drain screw |
Pfeil a | Constant oil flow for excessively large oil filling capacity and at start of oil adjustment |
Pfeil b | Correct oil filling capacity after draining off excess quantity |
P27.00-2330-05
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
Notes on automatic transmission | |||
Fill with transmission oil | |||
1 | Raise vehicle. | ||
The vehicle must be situated on the lifting platform so that it is level in both the longitudinal and transverse axes. | |||
2 | Remove bottom engine compartment paneling. | ||
3 | Remove drain screw (3). | Collect escaping transmission oil. | |
Commercially available devices/tools | |||
4 | Remove rear engine crossmember. | Only when operations were conducted on the transfer case. | |
MODEL 447 with CODE ZG2 (Permanent all-wheel drive) | |||
Do not remove support. | |||
5 | Lower transmission slightly. | MODEL 447 with CODE ZG2 (Permanent all-wheel drive) | |
6 | Remove drain screw of transfer case. | MODEL 447 with CODE ZG2 (Permanent all-wheel drive) | |
Collect escaping transmission oil. | |||
Commercially available devices/tools | |||
7 | Screw in drain screw of transfer case. | MODEL 447 with CODE ZG2 (Permanent all-wheel drive) | |
Drain screw to intermediate housing | |||
8 | Remove filling screw of transfer case. | MODEL 447 with CODE ZG2 (Permanent all-wheel drive) | |
9 | Fill transfer case with 0.7 l transmission oil. | MODEL 447 with CODE ZG2 (Permanent all-wheel drive) | |
| Automatic transmission fluids (ATF) (specification 236.15) | ||
10 | Screw in filling screw of transfer case. | MODEL 447 with CODE ZG2 (Permanent all-wheel drive) | |
Filling screw to intermediate housing | |||
11 | Install rear engine crossmember. | Only when operations were conducted on the transfer case. | |
MODEL 447 with CODE ZG2 (Permanent all-wheel drive) | |||
12 | Screw in adapter (2) of oil dispenser. | ||
| 000 588 06 82 00 Oil dispenser | ||
13 | Connect oil dispenser. | ||
| 000 588 06 82 00 Oil dispenser | ||
14 | Pump 6 l of transmission oil into transmission. | ||
| Automatic transmission fluids (ATF) (specification 236.15) | ||
| |||
On transmissions that have been repaired, add the quantity of transmission oil drained + 0.5 l. | |||
15 | Start engine. | ||
16 | Determine transmission oil temperature using diagnostic system. | ||
| Connect STAR DIAGNOSIS and read out fault memory | ||
When checking and correcting the transmission oil level, the transmission oil temperatures must always be maintained. | |||
17 | Bring transmission oil temperature in temperature range 40 to 45 °C or 104 to 113 ℉. | ||
18 | Switch off engine. | ||
19 | Determine transmission oil temperature using diagnostic system. | ||
| Connect STAR DIAGNOSIS and read out fault memory | ||
Transmission oil temperature must lie between 40 to 45 °C or 104 bis 113 ℉. | |||
20 | Start engine and run in selector lever position"P". | ||
21 | Pump transmission oil into transmission using oil dispenser. | After replacing the transmission and torque converter: | |
Automatic transmission fluid ATF | |||
Correct transmission oil level | |||
22 | Shift through "P-R-N-D" drive ranges several times with the brake actuated and the engine idling. | ||
23 | Run engine in selector lever position"P" at idle speed. | ||
24 | Determine transmission oil temperature using diagnostic system. | ||
| Connect STAR DIAGNOSIS and read out fault memory | ||
Transmission oil temperature must lie between 40 to 45 °C or 104 bis 113 ℉. | |||
25 | Remove adapter (2). | ||
26 | Allow a constant flow of oil to drain off when the oil filling capacity is too large at the start of the oil adjustment (arrow a) at the specified transmission oil temperature until the correct oil filling capacity is reached after draining off the excess quantity (arrow b). | | |
If the oil flow is not constant, then the transmission oil level has to be corrected (from operation step 19 onwards) and then adjusted again. | |||
27 | Screw in drain screw (3). | Replace seal. | |
Drain screw on oil pan | |||
28 | Switch off engine. | ||
29 | Install lower engine compartment lining. |
Automatic transmission |
Number | Designation | Transmission 722.9 | |||
BF27.00-N-1001-01A | Automatic transmission fluid ATF | Filling capacity - complete refill | Liter | 10,0 | |
Filling capacity - oil change | Liter | 9,0 | |||
Filling capacity, transmission oil change | with torque converter | Liter | 9,0 | ||
Filling capacity, transmission oil change | without torque converter | Liter | 5,5 | ||
Sheet | |||||
Sheet | - | ||||
Sheet | - | ||||
Sheet | - | ||||
Sheet | - | ||||
Referenced documents
- ad0000s200004e Connect STAR DIAGNOSIS and read out fault memory
- ah2719p000101nkb
- ah2719p000101nkb Notes on automatic transmission
- ar0060s1000e Lift/jack up vehicle
- ar2210s1170ea Remove/install rear engine cross member
- ar6120s1105e
- ar6120s1105e Remove/install lower engine compartment lining
- as0000z000501a Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running.
- bb0040p023615a Automatic transmission fluids (ATF) (specification 236.15)
- bb0040p023615a
- ws1800p0026b 000 588 06 82 00 Oil dispenser