1 | Nozzle of the equalizing tank |
2 | Clamp |
3 | Adaptor |
4 | Test device |
5 | Angular piece |
6 | Knurled nut |
W20.00-1014-12
| Check | ||
Warning | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure it with the safety strut. | |
1 | Position the heating temperature selector in "max heat"; fully open position | ||
Topical note | Notes on tilting the cab | ||
Model equipped with a heating system. | |||
Warning | Risk of injury caused by pinching and crushing when opening and closing engine hood | No one should be within the swivel range of the engine hood as it is being opened or closed. Always open engine hood all the way to the end position until this engages in the front locks. | |
2 | Tilt the cab | ||
3 | Remove the cap from the coolant equalizing tank (1) nozzle | ||
Topical note | Notes on coolant | ||
4 | Check the coolant level | | |
Cooling system - Approximate level | |||
5 | Dry the equalizing tank (1) nozzle | ||
6 | Rotate the sealing rubber on the adapter (3) to fit it to the bore of the equalizing tank (1) nozzle | Adapter | |
7 | Loosen the knurled nut (6) from the adapter (3) | ||
8 | Screw the angular piece (5) and the testing device (4) to the adapter (3) | Clamp | |
Adapter | |||
Tester | |||
9 | Using the testing device (4), install the adapter (3) to the equalizing tank (1) nozzle and fasten the clamp (2) to the knurled nut (6) on the adapter (3) | Engage the clamp (2) below the shoulder (arrows) on the coolant filling nozzle and pre-stress the clamp (2) with the knurled nut (6). | |
10 | Pressurize the cooling system on the testing device (4) with compressed air, and inspect the sealing of the cooling system | | |
In case of leaks in the cooling system, a constant pressure drop is visible on the gauge. | |||
Pressure drop in the cooling system | |||
11 | Perform a visual inspection on all cooling conductive components | | |
| |||
12 | Depressurize the testing device (4), remove the clamp (2) and remove the adapter (3) with the testing device (4) from the coolant equalizing tank (1) nozzle | ||
13 | Check the coolant level | Only in case of pressure drop in the cooling system. | |
Cooling system - Approximate level | |||
Check the concentration of additive in the coolant | |||
| |||
If necessary, adjust the concentration or replace the coolant. | |||
Warning | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within the tilting range of the cab as it is being tilted. Always tilt the cab all the way to the end position and secure it with the safety strut. | |
14 | Install the cap of the coolant equalizing tank | ||
Topical note | Notes on tilting the cab | ||
Warning | Risk of injury caused by pinching and crushing when opening and closing engine hood | No one should be within the swivel range of the engine hood as it is being opened or closed. Always open engine hood all the way to the end position until this engages in the front locks. | |
15 | Return the cabin to the work position |
655 589 00 63 00
Adapter
001 589 83 21 00
Tester
950 589 12 63 00
Clamp
Referenced documents
- ah2000n208001a Notes on coolant
- ah6080n000301a Notes on tilting the cab
- as6080z000101a Risk of injury caused by body parts being pinched or crushed as cab is tilted
- as8840z000101a Risk of injury caused by pinching and crushing when opening and closing engine hood