Remove/install oil filter housing with heat exchanger · ar1820p0001oln · Mercedes-Benz WIS

AR18.20-P-0001OLN

Remove/install oil filter housing with heat exchanger

27.07.2020

Engine

654.8 in model 213, 238, 257

Remove/install oil filter housing with heat exchanger

P18.20-A012-09

1	Oil filter housing with heat exchanger		3	Electrical connectors
2	Ball stud		4	Screws

 Danger	Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC)	Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines.	AS00.00-Z-0035-01A
 Caution	Risk of injury to skin and eyes due to handling of engine oil. Risk of poisoning caused by swallowing engine oil	Wear protective gloves, protective clothing and safety glasses. Do not fill engine oil into beverage containers.	AS18.00-Z-0001-01A
Topical note	Information on preventing damage to electronic components due to electrostatic discharge		AH54.00-P-0001-01A
Topical note	Information on preventing damage to electronic components due to electrostatic discharge		AH54.00-P-0001-01A
Topical note	Notes on avoiding damage through contamination and foreign objects		AH00.00-P-5000-01A
 	Remove/install
1	Remove electric coolant pump.		AR20.10-P-1281OLN
		 Installation: Only install upper engine cover after the leak test.
2	Remove charge-air distributor.		AR09.41-P-8683OLC
3	Release and disconnect electrical connector of refrigerant compressor.
4	Remove refrigerant compressor and place to one side with connected refrigerant lines.	Engine 654.8 in model 213 (except 213.011/016/211/216), 238, 257	AR83.55-P-5311OLN
5	Remove ball pin (2).	 Ball stud for engine cover to crankcase/oil filter housing	*BA01.10-P-1002-01D
6	Expose engine oil pressure and temperature sensor (B149/1).		AR18.40-P-4125OLN
		 Do not remove engine oil pressure and temperature sensor (B149/1).
7	Release and disconnect electrical connectors (3).
8	Remove electrical wiring harness from the oil filter housing with the heat exchanger (1).
9	Remove screws (4) in reverse numerical sequence from the bolt plan.	Bolt plan	AR18.20-P-0001-01OLC
		 Bolt, oil filter housing (major assembly carrier) to crankcase	*BA18.20-P-1004-01W
10	Remove oil filter housing with the heat exchanger (1) and collect escaping engine oil using a rag.	 Do not disconnect oil filter housing and heat exchanger. Leaks can occur otherwise.
		 Installation: Replace seals.
11	Remove oil spray nozzle shutoff valve (Y131).	When replacing oil filter housing with heat exchanger (1).
			AR18.40-P-2012OLC
12	Remove engine oil pressure and temperature sensor (B149/1).	When replacing oil filter housing with heat exchanger (1).
			AR18.40-P-4125OLN
13	Clean sealing surfaces on the oil filter housing with the heat exchanger (1) and crankcase with a lint-free cloth.
14	Install in the reverse order.
	Check
15	Check engine oil level and correct if necessary.
		Engine 654.8 in model 213, 238, 257 with code M014 (Engine uprated)	AP18.00-P-0101FA
 Warning	Risk of burn injuries, suffocation and poisoning when working on the exhaust system and the components connected to it. Risk of suffocation and risk of poisoning caused by inhalation of gaseous and solid components of the exhaust. Risk of poisoning caused by skin contact with solid components of the exhaust.	Wear protective clothing and safety glasses. Use the extraction system. Move people out of the hazard area.	AS49.00-Z-0001-01A
 Warning	Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running.	Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts.	AS00.00-Z-0005-01A
16	Perform engine test run. While doing so, check engine for proper operation and leak tightness.

 Engine cover

Number	Designation		Engine 654
BA01.10-P-1002-01D	Ball stud for engine cover to crankcase/oil filter housing	Nm	4

 Oil filter

Number	Designation			Engine 654.8
BA18.20-P-1004-01W	Bolt, oil filter housing (major assembly carrier) to crankcase	Stage 1	Nm	10
		Stage 2	Nm	19

Referenced documents

ah0000p500001a Notes on avoiding damage through contamination and foreign objects
ah5400p000101a Information on preventing damage to electronic components due to electrostatic discharge
ap1800p0101fa Engine oil and oil filter change
ar0941p8683olc Remove/install charge air distributor
ar1820p000101olc Bolt plan for oil filter housing with heat exchanger
ar1840p2012olc Remove/install shutoff valve for oil spray nozzles
ar1840p4125oln Remove/install engine oil pressure and temperature sensor
ar2010p1281oln Remove/install electric coolant pump
ar8355p5311oln Remove/install electric refrigerant compressor
as0000z000501a Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running.
as0000z003501a Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC)
as1800z000101a Risk of injury to skin and eyes due to handling of engine oil. Risk of poisoning caused by swallowing engine oil
as4900z000101a Risk of burn injuries, suffocation and poisoning when working on the exhaust system and the components connected to it. Risk of suffocation and risk of poisoning caused by inhalation of gaseous and solid components of the exhaust.